Brother 970MC - MFC B/W - All-in-One Owner'S Manual Download Page 113

Page: 113 / 165

C H A P T E R T W E L V E

Printing

Reports

103

FAX/MFC Settings and Activity

You can print the following lists and reports:

1.XMIT REPORT

Choose if Transmission
Verification Report is printed after
all faxes sent.

2.ACT.REPORT

Activity Report lists information
about the last 30 incoming and
outgoing faxes. TX means
Transmit; RX means Receive.

3.ALL DIAL

Lists names and numbers stored in
One Touch and Speed Dial
memory, in numerical order.

4.TEL.INDEX

ALL DIAL list (above), alphabeti

cally.

5.USER SETTINGS

Lists settings for INITIAL SETUP,
SETUP RECEIVE, SETUP
SEND, PRINT REPORTS and
TEL SERVICE. The settings for
REMOTE FAX OPT (for FAX 770
only) and for SETUP MSG CTR
and MSG CTR PRO (for FAX
870MC and MFC 970MC only)
are included.

6.MEMORY STATUS

Lists summary information and
amount of occupied memory.

Summary of Contents for 970MC - MFC B/W - All-in-One






































































































































































Search results

Summary of Contents for 970MC - MFC B/W - All-in-One

Reviews:

Related manuals for 970MC - MFC B/W - All-in-One

Brands by name

Popular brands

Brother 970MC - MFC B/W - All-in-One, Owner'S Manual

Search results

Summary of Contents for 970MC - MFC B/W - All-in-One

Reviews:

Related manuals for 970MC - MFC B/W - All-in-One

Brands by name

Popular brands