Basin mounted electronic tap for cold or premixed water.
P O W E R
S U P P LY:
6 X 1 . 5 V A A / 24 0 V-9 V T R A N S F O R M E R
M I N I M U M W AT E R P R E S S U R E :
2 0 0 K P A
M A X I M U M W AT E R P R E S S U R E :
5 0 0 K P A
I N A C C O R D A N C E W I T H A S 3 5 0 0
S E C U R I T Y S H U T O F F :
9 0 S E C O N D S D E FA U LT
H O T W AT E R T E M P E R AT U R E :
M A X 7 0 ˚ C
A D J U S TA B L E F L O W T I M E :
3 - 1 2 S E C O N D S
A D J U S TA B L E S E N S O R R A N G E :
8 0 M M - 1 7 0 M M
Before installing this unit, ensure that the listed precautions have been checked off.
Failure to do so will void warranty.
AV O I D R E F L E C T I O N I S S U E S
• The sensor eye must be installed no closer than 300mm to any adjacent surface.
• Do not install the unit with the sensor eye above a plug/waste in a basin or sink.
• This unit is not intended to be used with any reflective surface, such as polished stainless steel.
• Do not install the sensor facing a mirror or any other system operated by an infra-red sensor.
• Be aware of lighting that may reflect into basins/sinks that may reflect back into the sensor eye.
WAT E R S U P P LY
• A 500kpa pressure limiting valve, 60 mesh in line filter and an isolation valve must be installed in
line before the solenoid valve. Flush water supply lines thoroughly before installing the solenoid.
Do not allow dirt, Teflon tape or foreign particles to enter into the tap. All plumbing is to comply
with Australian Standards AS3500. Failure to do so will void warranty.
• These units are not suitable for gravity feed systems.
C O R R E C T S O A P V I S C O S I T Y
• Ensure that the correct soap is selected for the Brosmart Sensor Soap Dispensers. A soap with
no grit and a viscosity of 100-3800cPs is to be used. Failure to do so will void warranty. We
recommend using “Reward Distribution” Liquid Hand Soap (P/N: 3072120).
S E R V I C E A C C E S S
• Install the transformers and solenoids in a serviceable location (either behind a nearby service
access panel, or in the ceiling). Soap bottles need to be installed in an easily accessible location
to refill the bottles with soap.
• A minimum of 32mm conduit should be used to house the leads, to aid with drawing cables & plugs.
• Brodware have extension leads if required (sold separately). Do not cut or make your own. Doing
so will void warranty.
S E N S O R A D J U S T M E N T
• Adjustments to the sensor sensitivity and run time are done by using a specific remote control (
sold separately) for both the Brosmart Sensor Taps and Brosmart Sensor Soap Dispensers. If you
do not have one on site when installing, please contact you supplier.
If there are any issues with complying with any other above, please contact Brodware before
proceeding on 1300 800 300 or [email protected].
T E C H N I C A L D ATA
P R E - I N S TA L L AT I O N I N F O R M AT I O N
Wall mounted electronic tap for cold or premixed water.
P O W E R
S U P P LY:
B AT T E R Y O R 9 V T R A N S F O R M E R
M I N I M U M W AT E R P R E S S U R E :
2 0 0 K P A
M A X I M U M W AT E R P R E S S U R E :
5 0 0 K P A
I N A C C O R D A N C E W I T H A S 3 5 0 0
S E C U R I T Y S H U T O F F :
9 0 S E C O N D S
H O T W AT E R T E M P E R AT U R E :
M A X 7 0 ˚ C
A D J U S TA B L E F L O W T I M E :
3 - 1 2 S E C O N D S
A D J U S TA B L E S E N S O R R A N G E :
2 0 -2 5 0 M M
3
4
Summary of Contents for 2.2702.90
Page 13: ...I CSEN 210509...
