background image

Como Corner Installation Guide - vJUN19

 

1

 

The Majestic Shower Company Limited

 

17 Flitch Industrial Estate, Chelmsford Road, Dunmow, CM6 1XJ

 

Tel44 (0) 8448 001 500

 

Fac44 (0) 1279 635 074 [email protected] www.majesticshowers.com

 

 

 

 

Thank you for purchasing this Como shower enclosure. Please study these instructions 
carefully before assembly and installation.

 

 

Checking of Parts

 

Parts are listed at the beginning of this guide. Please check all supplied parts immediately 
upon receipt and contact the Majestic Shower Company in the event of any missing or 
damaged parts.

 

 

Handling of Parts

 

When handling glass, take care to ensure that corners or edges are not knocked. Do not 
place glass on hard surfaces - place cushioning material underneath to prevent the glass 
from shattering.

 

Unwrap all metal parts carefully to prevent damaging the plated surfaces.

 

 

Pre Installation Checks

 

Prior to undertaking installation, check the accuracy of the following against specifications 
for the particular installation location:

 

- Verticality and flatness of the wall. A maximum of 15 mm lean in or lean out of the wall 

relative to the floor or tray can be accommodated by the wall profiles.

 

- Levelness and flatness of the floor or rim of the shower tray.

 

 
 
 
 
 
 
 
 
 
 
 

 

  

DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS

 

 

Summary of Contents for Como vJUN19












Reviews: