BRIGHT OTF6000 Manual Download Page 58

Page: 58 / 72

9. Physical and Chemical Properties

Form:

Liquefi ed gas.

Appearance/colour:

Colourless.

Odour:

Slight, ether-like.

Boiling point:

-19ºC.

Flash point:

Does not fl ash.

Auto-ignition temperature:

368ºC.

Lower explosion limit:

No LEL and UEL was assigned at standard testing

conditions, 20ºC. Exhibits fl ame limits at temperatures

in excess of 28ºC.

Upper explosion limit:

No LEL and UEL was assigned at standard testing

conditions, 20ºC. Exhibits fl ame limits at temperatures

in excess of 28ºC.

Vapour pressure:

4.271 hPa at 20ºC.

Vapour pressure:

11.152 hPa at 54.4ºC.

Density:

1.17 g/cm

at 21.1ºC.

Ph:

Neutral.

Solubility in water:

0,373 g/l.

Partition coeﬃ cient

(n-octanol/water):

log Pow 1.6.

Relative vapour density:

4 (Air = 1.0).

8. Exposure controls / personal protection

Occupational

exposure limits:

Components:

Trans-1,3,3,3-Tetrafl uoroprop-1-ene

Basis:

Honeywell

Exceeding

factor:

N/A

Value type:

Time weighted

average

Form of

exposure:

N/A

Control

parameters:

800 ppm

Remarks:

We are not

aware of any

national

exposure limit.

Occupational

exposure

controls:

The Personal Protective Equipment must be in accordance with

EN standards: respirator EN 136, 140, 149; safety glasses EN 166;

protective suit EN 340,463, 468, 943-1, 943-2; gloves EN 374; safety

shoes EN-ISO 20345. The type of protective equipment must be

selected according to the concentration and amount of the dangerous

substance at the specifi c workplace. Avoid inhalation of vapour or mist.

Environmental

exposure

controls:

Avoid breathing vapours, mist or gas. Keep working clothes separately.

Do not smoke.

Engineering

measures:

Keep containers tightly closed in a cool, well-ventilated place. Keep

only in the original container at temperatures not exceeding 50ºC.

Keep away from direct sunlight.

Personal

protective

equipment:

Respiratory protection:

Remarks: In case of insuffi cient

ventilation, wear suitable

respiratory equipment. Wear a

positive-pressure supplied-air

respirator.

Hand protection:

Glove material: Vitron (R).

Heat insulating gloves.

Eye protection:

Goggles.

Skin and body protection:

Wear suitable protective

equipment. Protective footwear.

Instruments

Office:

Bright Instruments LTD
Burnett House, Lakeview Court
Ermnie Business Park, Huntingdon
Cambridgeshire, PE29 6UA

Telephone: +44 (0) 808 168 9697
Email: [email protected]

Web: brightinstruments.com
Member:

Cryospray 1234ze

MATERIAL SAFETY DATA SHEET

Summary of Contents for OTF6000









































































Search results

Summary of Contents for OTF6000

Reviews:

Related manuals for OTF6000

Brands by name

Popular brands

BRIGHT OTF6000, Manual

Search results

Summary of Contents for OTF6000

Reviews:

Related manuals for OTF6000

Brands by name

Popular brands