BRIGHT OTF6000 Manual Download Page 52

Page: 52 / 72

OTF6000 Cryostat

Instruments

Office:

Bright Instruments LTD
Burnett House, Lakeview Court
Ermnie Business Park, Huntingdon
Cambridgeshire, PE29 6UA

*Included in standard order. **Additional Options.
† No discount applicable. VAT not included - E & OE

Telephone: +44 (0) 808 168 9697
Web: brightinstruments.com

OBJECT HOLDERS

Code

Description

50734-1*

Object holder, 22mm diameter, solid.

50734-2

Object holder, 22mm diameter, solid, as 50734-1 but long type.

50734-4

Object holder Brass 22 diameter.

50735-1*

Object holder, 37mm diameter, solid.

50735-2

Object holder, 37mm diameter, solid, as 50735-1 but long type.

50744

Object holder, 5mm diameter, solid.

50721

Object holder, 50mm diameter.

50741

Object holder, 50 x 50mm.

50743

Object holder, 50 x 70mm.

54229

Object Holder Stepped 16mm short.

50720

Orientating object holder, 22mm diameter, for use with item 51695.

50719

Orientating object holder, 37mm diameter, for use with item 51695.

50718

Orientating object holder, 50mm diameter, for use with item 51695.

50712

Orientating object holder, 50 x 50mm, for use with item 51695.

50745

Orientating object holder, 5mm diameter, for use with item 51695.

50221

Quick release object holder clamp, complete with 50 metal object discs.

50727

Hollow object holde 22mm.

50690

Metal object holder discs, 22mm, pack of 50.

50204

Cork object holder discs, 22mm, pack of 50.

50204-1

Cork object holder discs, 50 x 50mm, pack of 50.

54168

Prostate Cryomould Former L22 x W6 x D4mm

54170

Quick release object holder strip clamp, complete with 10 of part number 54171

52658

Vertical vice clamp.

52632

Vertical vice clamp, 45º.

Order List 202

EQUIPMENT OPTIONS

Code

Description

Low Spec

High Spec

Footswitch for motor drive Leaves hands free

to collect sections. (P/Nbr: 138026).

Optional

Standard

ORIENTATION

Code

Description

50539

Orientating head assembly. With fi ne object orien/-8º in

horizontal and vertical axes, 360º rotation.

50627

Orientating head assembly. Without fi ne adjustment screws

51695

Universal head assembly for orientating object holders. Used on

instruments without the factory fi tted orientation system. This fi ts

into the standard specimen clamp in place of the V-block and permits

a range of orientating object holders to be used. NB Not compatible

with /D cryomatic specimen temperature control.

Code

50255-1

Description

0.5 - 30μm feed screw.

50257-1

1 - 60μm feed screw.

50258-1

2 - 120μm feed screw.

FEED SCREWS FOR / MAR OPTION

Summary of Contents for OTF6000









































































Search results

Summary of Contents for OTF6000

Reviews:

Related manuals for OTF6000

Brands by name

Popular brands

BRIGHT OTF6000, Manual

Search results

Summary of Contents for OTF6000

Reviews:

Related manuals for OTF6000

Brands by name

Popular brands