Page 26
7
Lift Installation Instructions
Warnings and Lift
Operating Instructions
Decal 28540
Decal Application
WARNING
Affix Warnings and Lift
Operating Instructions decal
28540 and ADA Standee
and Interlock decal 19342 to
the vehicle door in a highly
visible location near the
control box as shown. Two
Courtesy Requested decals
are supplied to be posted on
the vehicle as desired.
Replace any missing, worn
or illegible decals!
9
ADA Standee
and Interlock
Decal 19342
OPERATING
INSTRUCTIONS
19342
Standees must
stand at center of platform (fully inside
yellow boundaries), grip handrails and
lower head to clear door jamb header.
Lift Interlocks
vary in type and operation. Interlock
(if equipped) must be operated as
instructed by transit authority.
Read warnings and operate lift as
outlined on LIFT OPERATING
INSTRUCTIONS decal. Lift operating
instructions apply to wheelchair
passengers and standees.
Standee Instructions:
Interlock Instructions:
Replace missing, worn
or illegible decals.
Failure to do so may
result in serious bodily
injury and/or property
damage.
Platform Angle Adjustment and Floor Level Adjustments
Note:
Clean surfaces with
isopropyl alcohol before decal
application. Use a clean cloth
or paper towel.
Do not
use
oily shop rags. Wipe surface
free of residue with dry
portion of cleaning cloth.
WARNING
LIFT OPERATING
INSTRUCTIONS
¥ Read manual before operating lift.
¥ Load and unload on level surface
only.
¥ Engage vehicle parking brake before
operating lift.
¥ Provide adequate clearance outside
of vehicle to accommodate lift.
¥ Do not operate lift if you suspect lift
damage, wear or any abnormal
condition.
¥ Keep operator and bystanders clear
of area in which lift operates.
Whenever a wheelchair passenger
is on the platform, the:
¥ Handrail belt must be latched
¥ Passenger must be positioned
fully inside yellow boundaries
¥ Wheelchair brakes must be locked
¥ Roll stop(s) must be up
Failure to follow these rules may result
in serious bodily injury and/or property
damage.
Note: Handrail belt must be
latched to operate lift.
OPEN DOOR(S) AND SECURE
TO UNFOLD PLATFORM:
Stand clear and press UNFOLD
switch until platform stops (reaches
floor level).
Note: In event platform does not
unfold, press FOLD switch to
release Lift-Tite“ latches.
TO UNLOAD PASSENGER:
1. Load passenger onto platform and
lock wheelchair brakes.
2. Press DOWN switch until entire
platform reaches ground level and
roll stop unfolds fully.
3. Unlatch handrail belt.
4. Unlock wheelchair brakes and unload
passenger from platform.
TO LOAD PASSENGER:
1. Load passenger onto platform and
lock wheelchair brakes.
2. Latch handrail belt.
3. Press UP switch to fold roll stop
up and raise platform to floor level.
4. Unlock wheelchair brakes and unload
passenger from platform.
TO FOLD PLATFORM:
Press FOLD switch until platform
stops. Release switch.
CLOSE DOOR(S)
28540
U.S. Patents: 5,261,779
6,065,924 6,238,169 Patents Pending
Adjust platform
angle and bridge
plate floor level
position as detailed
in this manual
before operating lift
with a passenger.
Failure to do so may
result in serious
bodily injury and/or
property damage.
WARNING
The platform angle and floor
level positioning of the bridge
plate (inboard roll stop)
must be
properly adjusted before
operating the lift with a pas-
senger
.
Adjust the platform angle as
detailed in Platform Angle Adjust-
ment Instructions on pages 28
and 29.
Adjust the floor level positioning of
the bridge plate (inboard roll stop)
as detailed on pages 30 and 31.
Base Plate Plugs
8
Two plastic plugs (1" I.D.
x 1-1/4" O.D. end caps)
are supplied. Insert one
plug in each of the two
inboard base plate
mounting holes as shown
in Figure T (if applicable).
Figure T
Plastic
Plugs
Summary of Contents for CENTURY CL917IB
Page 58: ...Page 38 Note Note This page intentionally left blank...
Page 94: ......
