BRANNSTROM CleanTrack 1000 B, Operation And Technical Manual, Page: 93 / 232

Brannstrom Sweden AB CleanTrack 1000B - Rev 2.20xd, 2019 Page 93 of 232
Every 6 months:
1. Inspect the interior of all cabinets for general condition and cleanliness.
2. Check all components with respect to mounting, clamping of cables, and any signs of damage.
3. Check all connections to be tightened and not leaking.
4. Check the cables to the analyzing unit and sample pump along their entire length with respect to any signs of
chafe, wear or other damage and the bulkhead penetrations to be in proper conditions.
5. Check the sample pump:
If sample pump SPP-100 with Ex motor:
See Sample pump SPP-100 with Explosion proof electric motor page 12.
1. Check the setting of the sample pump. In chapter 7.8.8. System Configuration, Standard page 71
verify that the setting of property “Sample Pump” is “Suzhong SPP-100”.
2. Refer to makers MAINTENANCE part in chapter 12.8.1. Elprom instructions page 201
If sample pump is bulkhead mounted:
See Sample pump Nikuni 32MED22/Matre P06 for Bulkhead mounting page 12
1. Check the setting of the sample pump. In chapter 7.8.8. System Configuration, Standard page 71
verify that the setting of property “Sample Pump” is “Nikuni 32MED22” or “Matre P06”.
2. Check the oil level in the sample pump shaft seal.
See chapter 9.7. Sample Pump Shaft seal oil refilling page 93
If sample pump with air motor:
See Sample pump Speck Y-2951 with Air driven Gast motor page 12 .
1. Check that all air supply valves to the air motor are closed.
2. Refer to makers MAINTENANCE part in chapter 12.9. Sample Pump, Speck pump with Gast air
motor page 228 .
6. For upgraded units with serial numbers earlier than CTB 2892 and with electrical sample pump motors:
Check that the sample pump motor contactor feedback is wired and enabled.
See chapter 7.8.9. System Configuration, Alarms&Extras page 71 and the setting of the property
“ConvertingUnitType” is “PumpFeedback”.
7. In case of computer or converting unit malfunction:
See chapter
8.1. Malfunction of Computer/Converting unit
page
82.
9.5. Verification of accuracy and access to restricted parts
User access to the Measuring cell is restricted with seals, which only Brannstrom Sweden AB can replace, in order to
comply with clause 5.1 of MEPC. 108(49).
A calibration certificate is issued by Brannstrom Sweden AB when the CleanTrack 1000B is new. Later on, an
“Accuracy Verification Certificate” can only be issued by Brannstrom Sweden AB or its approved agents.
The validity of the calibration certificate is max 5 years. Once the factory issued calibration certificate has expired the
measuring cell must be replaced. The calibration certificate should be retained on board for inspection purpose.
9.6. Cleaning of Inlet Filter
When CleanTrack 1000B is in “StandBy” mode, close the sample inlet probe valves, open the drain valve and close the
Analyzing unit inlet valve. Remove and clean the filter screen. Usage of CleanTrack 1000B sample pump unit without
the inlet filter screen could harm the sample pump.
The Inlet Filter is item 15 in drawing 10.9.1. Partnames of typical arrangement page 129 .
9.7. Sample Pump Shaft seal oil refilling
This part does only apply to CleanTrack 1000B versions with bulkhead penetration sample feed pumps.
The oil reservoir is positioned in the engine room side. Remove the oil reservoir cover nut. Be careful not to unscrew
the reservoir from the pump. Refill up to the thread with recommended oil type. Be careful not to harm the plastic
reservoir when the cover nut is mounted. Turn the cover nut Clock Wise until it is in right position.
See chapter 10.5. Nikuni Sample pump for Bulkhead mounting page 121
or chapter 10.6. Matre Sample pump for Bulkhead mounting page 124 .