BRANNSTROM CleanTrack 1000 B, Operation And Technical Manual, Page: 92 / 232

Brannstrom Sweden AB CleanTrack 1000B - Rev 2.20xd, 2019 Page 92 of 232
9. Maintenance, Spare parts and Consumables
9.1. Software upgrading
The software in the Computer unit can be upgraded via a USB memory stick attached to the USB port at the front of the
computer unit.
It is recommended to contact an authorized agent for the software upgrade.
Three parts are needed for an upgrade:
1. A file containing the software. In the name of the software file the software version, year and day of
creation are mentioned. The extension is “.deb”.
2. A particular document, step by step guiding through the upgrade procedure. This document contains a
description of the significant changes and might also recommend hardware updates needed to fully take
use of the new software.
3. A serial number specific access password which the unit will ask for before the upgrade can take place.
This password is normally provided by an authorized agent.
9.2. Battery replacement
The Computer unit CPU printed circuit board contains a Lithium battery, type CR1225 3V.
For location, see drawing CTB10001p sheet 3, Computer Unit with open door page 98 , d4.
The battery is powering the Real Time Clock for keeping time when power is switched off to the Computer Unit.
A battery failure will affect the Real Time Clock, the Power Off Time and Accumulated Total Oil Discharged.
After a battery failure and a power off:
Real Time Clock must be set, see chapter 7.9.2. Real Time Clock page 73
Power Off Time on Recorded data (1:st printout after Power On) will be faulty.
Accumulated Total Oil Discharged will need a reset, see chapter 7.2.2. Running Settings page 47
9.3. Saving Printouts and Settings on a USB memory stick
The recording device is formatted electronically as mentioned in MEPC.108(49) chapter 6.9.1.
Recorded data is stored in a non-volatile memory and can hold approximately 3,000,000 printouts.
Recorded data can be copied to a USB-memory stick.
Refer to chapter
7.1. Main Menu
page
45
and chapter
7.5. USB
page
56.
All settings made to set up the individual CleanTrack can also be saved to a USB memory stick. This backup file named
“CTB-####_setup.txt” can be used if the Computer unit CPU card needs to be replaced in the future. The file can then
be mailed to info@brannstrom.se and be preinstalled on the new CPU card.
Refer to chapter 7.1. Main Menu page 45 and chapter 7.5. USB page 56.
9.4. Periodic Checks and Servicing
Certain checks and servicing should be carried out at regular intervals in order to minimize the risk for unexpected
malfunctions during operation. Below is a maintenance list to be carried out after each use and another list to be carried
out at regular intervals of 6 months.
After each time of usage:
1. Check that chapter 5.3. Close down procedure page 39 has been followed.
2. If the unit shall not be used for a longer time or sub-zero conditions might arise,
See chapter 5.4. Closing down for a longer time or preserving for sub-zero conditions page 39 .
3. Check mounting and cable penetrations of motor to be tightened and in order.
4. Check pump connections and fittings to be tightened and in order
5. Check the installation and the components for signs of leakage. Clean if necessary.
6. If bulkhead mounted sample pump: check the oil level in the sample pump shaft seal.
a. See chapter 9.7. Sample Pump Shaft seal oil refilling page 93 .
7. Check that all manually operated sample valves are closed.
8. If paper printer: check the amount of printer paper that is left and replace the roll if necessary, for safeguarding
uninterrupted operation during next discharge.
9. Consider to store “Recorded data” on a USB-memory stick. See chapter 7.5.1. USB-Memory stick page 56 .