Brammo 2013 Empulse Owner'S Manual Download Page 90

Page: 90 / 112

Identification Numbers

Technical Information

Technical Information

Identification Numbers

IDENTIFICATION NUMBER LOCATIONS

The Vehicle Identification Number (VIN) and motor serial number are
required when you register your Empulse. They may also be required
when ordering replacement parts.

Vehicle Identification Number (VIN)

The 17-digit VIN is stamped onto the frame’s steering head behind
the headlight. Turn the handlebars fully left to view the number,

Note:

The VIN is also shown on the safety certification label. See

“SAFETY LABELS”, page 6

Motor Serial Number

The motor serial number is located on a label on the underside of
the motor.

Empulse.book Page 88 Thursday, June 27, 2013 11:03 AM

Summary of Contents for 2013 Empulse

















































































































Search results

Summary of Contents for 2013 Empulse

Reviews:

Related manuals for 2013 Empulse

Brands by name

Popular brands

Brammo 2013 Empulse, Owner'S Manual

Search results

Summary of Contents for 2013 Empulse

Reviews:

Related manuals for 2013 Empulse

Brands by name

Popular brands