Brammo 2013 Empulse Owner'S Manual Download Page 35

Page: 35 / 112

Batteries and Charging

Charging and Battery Care

CHARGING THE EMPULSE

Your Empulse is designed to take a charge from any J1772 electric
vehicle charger (Level 1 - 110V or Level 2 - 240V).

1. Position your Empulse as close as possible to an available AC wall

outlet.

2. Open the charging cap on the Empulse by pressing the vertical

tab forward.

3. Plug the J1772 charging connector into the charging receptacle

on the Empulse. Once connected, charging automatically starts.
The key should be removed for security when charging in public.
As a safety feature, the headlight stays on while the Empulse is
charging.

During charging, the battery charging indicator on the
instrument cluster is illuminated orange.

When charging is complete, or at 100% State of Charge (SoC)
the battery charging indicator turns green.

WARNING

The use of an extension cord is not recommended, as they can
increase the risk of electric shock or other hazards (e.g., fire and trip).

Empulse.book Page 33 Thursday, June 27, 2013 11:03 AM

Summary of Contents for 2013 Empulse

















































































































Search results

Summary of Contents for 2013 Empulse

Reviews:

Related manuals for 2013 Empulse

Brands by name

Popular brands

Brammo 2013 Empulse, Owner'S Manual

Search results

Summary of Contents for 2013 Empulse

Reviews:

Related manuals for 2013 Empulse

Brands by name

Popular brands