Brammo 2013 Empulse Owner'S Manual Download Page 13

Page: 13 / 112

Gauges, Indicators, and Displays

Controls and Instruments

LIQUID CRYSTAL DISPLAY (LCD)

When the Empulse powers up, the LCD will temporarily show all
black so you can make sure it is functioning properly. The LCD
backlight is always illuminated when the Empulse is powered up.

Note:

If any part of the display does not come on, or the backlight is not

illuminated, contact your Brammo Authorized Dealer as soon as
possible.

Drive mode

1. Battery State of Charge (SoC)

2. Current time

3. SPORT operating mode selected

4. Speed (mph or km/h)

5. Gear selected

6. Information - press the mode button to cycle through the

following functions.

•

Power consumption in kilowatts

•

Air temperature

•

Motor temperature

•

Estimated range remaining

7. Odometer/Trip display

Charge mode

1. Charging rate for the connected supply

2. Estimated time remaining to fully charge the Empulse

Empulse.book Page 11 Thursday, June 27, 2013 11:03 AM

Summary of Contents for 2013 Empulse

















































































































Search results

Summary of Contents for 2013 Empulse

Reviews:

Related manuals for 2013 Empulse

Brands by name

Popular brands

Brammo 2013 Empulse, Owner'S Manual

Search results

Summary of Contents for 2013 Empulse

Reviews:

Related manuals for 2013 Empulse

Brands by name

Popular brands