Brammo 2013 Empulse Owner'S Manual Download Page 62

Page: 62 / 112

Maintenance

Servicing and Maintaining Your Empulse

Refilling the transmission oil

The transmission should be filled with the Empulse standing on level
ground and supported on the kickstand.

1. Fill the transmission with approximately 1.0L (1 quart) of

Synthetic 10W-30 API GL-1 Motorcycle oil (wet clutch approved).

2. Install the oil filler plug and tighten to 15 Nm.

3. Clean the exterior of the transmission to remove any oil deposits.

Disposal of used transmission oil

WARNING

It is illegal to pollute drains, water ways or soil. Only use authorized
waste disposal sites to dispose of used oil and other fluids from the
Empulse.

Empulse.book Page 60 Thursday, June 27, 2013 11:03 AM

Summary of Contents for 2013 Empulse

















































































































Search results

Summary of Contents for 2013 Empulse

Reviews:

Related manuals for 2013 Empulse

Brands by name

Popular brands

Brammo 2013 Empulse, Owner'S Manual

Search results

Summary of Contents for 2013 Empulse

Reviews:

Related manuals for 2013 Empulse

Brands by name

Popular brands