Brammo 2013 Empulse Owner'S Manual Download Page 17

Page: 17 / 112

Setting the Time

Controls and Instruments

Setting the Time

SETTING THE TIME

The time and date on your Empulse were set at the factory to Pacific
Standard Time. If you need to adjust the time on your Empulse:

1. Connect the charging connector to the Empulse and a wall

outlet. This will put the Empulse in charging mode.

2. Press and hold the Mode and Trip buttons simultaneously for

approximately two seconds to enter Setup mode.

3. Press the Mode button to select either HOURS or MINUTES.

4. Press the Trip button to increase the selected setting.

5. Once you have finished adjusting the time, press the MODE

button to select EXIT and then press the Trip button to confirm.

Note:

If no button is pressed for more than 30 seconds, the Empulse

will revert back to Charging mode.

6. Disconnect the charging connector from the Empulse.

Empulse.book Page 15 Thursday, June 27, 2013 11:03 AM

Summary of Contents for 2013 Empulse

















































































































Search results

Summary of Contents for 2013 Empulse

Reviews:

Related manuals for 2013 Empulse

Brands by name

Popular brands

Brammo 2013 Empulse, Owner'S Manual

Search results

Summary of Contents for 2013 Empulse

Reviews:

Related manuals for 2013 Empulse

Brands by name

Popular brands