Brammo 2013 Empulse Owner'S Manual Download Page 76 | Manualshive

Page: 76 / 112

background image

Transporting Your Empulse

74

Storage and Transportation

Transporting Your Empulse

TRANSPORTATION INFORMATION

If your Empulse needs to be transported, it should be carried on a
motorcycle trailer or a truck or trailer with a flatbed area. Do not tow
your Empulse.

When contacting a towing or transporting service, be sure to ask if
they have a flatbed area, loading ramp, or power ramp to safely lift
the Empulse. Also ask if they have motorcycle tie-down straps.

Use tie-down straps over each lower triple clamp to secure your
Empulse.

Tighten the tie-down straps until the front forks are compressed.

Note:

Do not fully compress the forks, as this may damage them.

Empulse.book Page 74 Thursday, June 27, 2013 11:03 AM

«
...
74
75
76
77
78
...
»

Summary of Contents for 2013 Empulse

















































































































Reviews:

No comments

Related manuals for 2013 Empulse

Brand: X-lite Pages: 5

ALK.00.733.15000/B

Brand: SW-Motech Pages: 14

Brand: LSL Pages: 4

Brand: MSA Pages: 163

Brand: Dakota Digital Pages: 6

Brand: KYMCO Pages: 424

PowerCom INNOVA Plus Business

Brand: AKE Pages: 2

Brand: R&G Pages: 6

Brand: Bajaj Pages: 39

Dirt rocket XM500

Brand: X-TREME scooter Pages: 14

Brand: DYNATEK Pages: 12

Brand: Pagsta Pages: 47

Brand: Yamaha Pages: 93

Brand: Yamaha Pages: 114

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands