background image

Installation 

P.O. Box 309

Menomonee Falls, WI 53052 USA

800 BRADLEY (800 272 3539)

+1 262 251 6000

bradleycorp.com

HDWC-INSTR-045 Rev. A: ECO 20-14-002S

© 2021 Bradley

Page 1 of 33 

6/25/2021

Phenolic Privacy Restroom Partitions, 

Floor-to-Ceiling – Series 700

*HDWC-INSTR-045*

For 69", 72" & 69"/72" Tall 

Doors and Panels Only

Table of Contents

Safety Information   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .2
Supplies Required  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .3
Hardware Provided   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .3
Example of Submittal Drawing .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .3
Door Descriptions & Part Numbers  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .4
Pilaster Descriptions & Part Numbers  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .5
Pilaster Configurations & Part Numbers  .  .  .  .  .  .  .  .  .  .  .  .  .6
Pilaster Configurations & Part Numbers – 69"/72"   .  .  .  .  .7
Pilaster Configurations & Wall Hung Part Numbers   .  .  .  .8
Layout Dimensions for Brackets   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .9
Mounting Brackets to Wall  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .10
Leveling Screws to Pilaster   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .11
Mounting Brackets to Pilaster   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .12–13
Pilaster Mounting Hardware   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .13–14
Pilasters and Panels   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .15–18
Wall-Hung Pilasters  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .19–22
Pilaster Shoes   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .23
Hinges   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .24–25
Door Hardware .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .26–31
Urinal Screens  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .32–33

Read the instructions in this manual before beginning installation. Save these instructions 
and refer to them for inspection, maintenance, and troubleshooting information.

For questions regarding the operation, installation or maintenance of this product, visit bradleycorp .com  
or call 800 .BRADLEY (800 .272 .3539) .

Product warranties and parts information may also be found on our website at bradleycorp .com .

Summary of Contents for Bradmar 700 Series


































Reviews: