background image

5

System deactivation by means of magnetic switch

It is also possible to force temperature control exclusion via the use of a magnetic window 
switch connected to the relevant terminals. This helps to avoid wasted energy. The activa-
tion of this mode is indicated on the display by the word 

.

Frost Protection Control

Whenever temperature control on the TA450 is bypassed, either manually or automatically, 
differential FROST protection remains active thus safeguarding both the boiler and the water 
pipes. The FROST PROTECTION temperature is programmable from +3°C to +16°C.

+3°C

–3°C

Temperature measurement calibration

Should the positioning of the TA450 not prove to be ideal (for example when situated close 
to a heat source) temperature measurement can be inaccurate: to overcome this problem 
the reading can be calibrated by +/– 3°C thus optimising comfort and energy consumption.

Thermal differential control

This control system is recommended for installations that are particularly difficult to control 
such as those that experience extreme variations in external temperature. It guarantees 
maximum benefit from the installation with minimum consumption. In order to adapt the 
system to installations that feature differing thermal inertias (convector heaters, underfloor 
heating, electric heaters) the temperature differential can be set between 0°C and 0 9°C

PI

Proportional/Integral Control

Allows for the optimisation of fuel consumption while enjoying the maximum of environ-
mental comfort by reducing the number of times the boiler is ignited as a function of the 
difference between the set temperature and room temperature: the smaller the difference 
between the two temperatures the fewer the number of times the boiler is ignited thus 
leading to a considerable reduction in energy consumption while maintaining a certain 
degree of comfort. The TA450 allows for the selection from among three preset programmes 
depending on the type of system to control (P1, P2 and P3). Alternatively programme P4, 
which is completely manual, can also be selected (See table 1 on page 18).
Integral proportional adjustment has the advantage of permitting the management of a 
wider variety of systems with respect to the setting of the thermal differential. It is especially 
suitable for underfloor and radiant systems. The difference between the set temperature 
and the ambient temperature is just a few tenths of a degree. This allows for more precise 
adjustment.

Temperature Set-point Adjustment Blocking

The TA450 can block the programming of temperature set-points thus avoiding accidental 
changes to settings. Using this feature the user is free to select one of three pre-pro-
grammed levels without the possibility to change them.

Summary of Contents for TA 450

























Reviews: