Solution 64 | Installer Guide | Comms Programming
9-6
Bosch Security Systems | 11/05 | BLCC110I
Alarm On Telephone Line Fail If Disarmed
This option sets the panel to trigger an alarm when the telco line
fails provided that the area is turned OFF or disarmed. In a multi-area
system this option is global and will be triggered if only one area in
the system is in the disarmed state. The alarm will continue to sound
until a valid PIN is entered or the siren timer expires.
Display ‘Phone In Use’
This option allows the keypad to display Phone In Use when the
telephone line has been looped by the control panel for either
incoming or outgoing calls. If this option is disabled, no indication is
provided on the keypad.
i
Note
The dialler status indicator LED located on the main panel will
always show the status of the dialler. See Section 3 - Wiring
Diagrams for more information.
Comms > Properties >
Country
MENU 5-2-3
0 = Australia
0
1 = New Zealand
6 = Portugal
11 = China
2 = Italy
7 = Hungary
12 = Hong Kong
3 = Greece
8 = Czech Republic
13 = Malaysia
4 = Cyprus
9 = Poland
14 = Brazil
5 = Spain
10 = Bulgaria
15 = Reserved
This menu automatically sets the dialling parameters including
dial and busy tones etc. for the country the panel is working in.
(*** System Wide Parameter ***)
Press [MENU] + [5] + [2] + [3]. The keypad will display the
currently selected country. The default country is Australia.
Use the up and down arrow keys to select the appropriate
country then Press [OK].
C001 AUSTRALIA
C002 NEW ZEALAND
C003 ITALy
Press
OK or MENU
Press [OK] to confirm and save and exit or press [MENU] to exit
without saving.
WARNING: Press OK to set
dialler to,
AUSTRALIA
i
Note
For correct dialler operation, you must make sure that the
correct country selection is made for your location. If your
country is not listed here please contact your Bosch distibutor.
1)
2)
4)
Comms > Properties >
Set SMS Password
MENU 5-2-7
p
a
s
s
w
d
This menu sets the SMS password which is required whenever
SMS reporting is selected. The password will typically be
defined by the service provider or Telco carrier who you are
using to route the message.
By default the SMS password is set to suit the Telstra Network
in Australia.
Enter [MENU] + 5+2+7. The keypad will display the current SMS
password.
Use the arrow and number keys to move and change text.
When the password is complete, press [OK]. At any time you
can press the [OFF] key to clear the text from the current cursor
position to the end of the line.
SMS Pager Password
passwd
Press
OK to SAVE
i
Note
See Alpha Text Programming in Section 4 - Programming
Overview for further detail on entering alpha text.
Comms > Remote Access >
Call Back Number
MENU 5-3-0
1
Digits
32
This menu sets the call back telephone number which can be
used to establish a SolutionLink RAS connection to the panel
for remote programming. The remote computers modem
should be connected to this number and Solutionlink should
be set to wait for an incomming call.
The installer or customer can force the panel to dial this
number by entering MENU 5-0-1.
For higher security the panel can be configured to always
use this number for callback verification when establishing a
SolutionLink remote access connection. The following steps
outline the callback procedure.
Step 1)
Use Solutionlink RAS to call panel from remote computer.
Step 2)
Panel will answer, acknowledge the request and then hang
up.
Step 3)
Panel will then dial the callback number.
Step 4)
SolutionLink will answer the call and establish a RAS session.
i
Note
See MENU 5-3-4 to force Callback Verification for every RAS
session.
1)
2)
