Bosch Rexroth IndraControl S67 Series Application Description Download Page 37

Page: 37 / 142

Connecting Data and Supply Cables

6.1

Notes

Voltage!

WARNING

Operate IndraControl S67 components exclusively with DC 24 V PELV (pro‐

tective extra-low voltage) or SELV (safety extra-low voltage) voltage sources.

Non-compliance can result in electric shock.

Highest current carrying capacity of supply

contacts is 4 A!

NOTICE

Observe the maximum current carrying capacity per supply line (U

, U

) as

well as the total current consumption for all IndraControl S67 components.

Both values must not exceed 4 A, as an increase in current causes the con‐

tacts to overheat and damages the IndraControl S67 components.

Open connections!

NOTICE

If connections have not been closed with protective covers, liquid or dirt can

penetrate the IndraControl S67 components and destroy them. Protect all

non-required connections with protective caps to be ordered separately (see

chapter 12.9 "Protective caps" on page 131

) to comply with protection class

IP 67.

●

The male connectors must be disconnected from the power supply be‐

fore screws are tightened.

●

Tighten the male connectors only by hand. Using mechanical tools can

cause the threads to strip. In such a case, replace the field bus coupler.
Tightening torques for connectors are: 0.6 Nm

●

Check the exact positioning (coding) between plug and socket

●

Use only ready-made Bosch Rexroth system cables to transmit the pow‐

er supply and for the S-BUS. This achieves the specified characteristic

values of technical data.

●

Keep sufficient distance between all cables and electromagnetic inter‐

ference sources to achieve a high noise immunity of the IndraControl

S67 system against electromagnetic emissions.

●

Note the minimum bending radius of Bosch Rexroth system cables (see

chapter 12.5 "Ready-made Sercos III Cables" on page 128

)

●

When laying the cables, ensure not to lay cables in shear areas of mov‐

ing machine parts

●

Connect the cable shield of the field bus cable to the functional ground

at both ends across a wide area.

●

Ensure the correct layout of the potential equalization

●

Do not use drop stubs, as increased line reflections and signal distor‐

tions are caused! This worsens the transmission properties significantly.

DOK-CONTRL-S67S3BKDI8*-AP03-EN-P
Rexroth IndraControl S67 Sercos Coupler 8 Digital Inputs (M8)

Bosch Rexroth AG

35/139

Connecting Data and Supply Cables

Summary of Contents for Rexroth IndraControl S67 Series















































































































































Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Related manuals for Rexroth IndraControl S67 Series

Brands by name

Popular brands

Bosch Rexroth IndraControl S67 Series, Application Description

Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Related manuals for Rexroth IndraControl S67 Series

Brands by name

Popular brands