Bosch Rexroth IndraControl S67 Series Application Description Download Page 117

Page: 117 / 142

Error code Error argu‐

ment

Cause

Troubleshooting

Error in parameter database

of the field bus coupler

Restart by disconnecting the

power supply and then re‐

connecting it. Contact

Bosch Rexroth Service if the

problem persists

Version of parameter

database is not supported

Number of I/O modules

does not match number en‐

tered into the parameter da‐

tabase (I/O module re‐

moved or deleted)

Error in parameter database

of the field bus coupler

Internal error

Restart by disconnecting the

power supply and then re‐

connecting it. Contact

Bosch Rexroth Service if the

problem persists

15
16

Ordering numbers of I/O

modules differ from the

numbers saved in the pa‐

rameter database (e.g. S67-

AI4-U/I-M12 instead of S67-

AI4-RTD-M12)

Replace the I/O module with

the one with the correct or‐

dering number

Internal error

Restart by disconnecting the

power supply and then re‐

connecting it. Contact

Bosch Rexroth Service if the

problem persists

The saved parameters can‐

not be applied to the I/O

module, as
- there is an incompatible

firmware release (after cre‐

ating the parameter data‐

base, one or more modules

were replaced from an

IndraControl S67 node.

These modules have an in‐

compatible firmware release

compared to the original

ones)
or
- a communication error oc‐

curred

Restart by disconnecting the

power supply and then re‐

connecting it

Error in parameter database

of the field bus coupler

Restart by disconnecting the

power supply and then re‐

connecting it. Contact

Bosch Rexroth Service if the

problem persists

DOK-CONTRL-S67S3BKDI8*-AP03-EN-P
Rexroth IndraControl S67 Sercos Coupler 8 Digital Inputs (M8)

Bosch Rexroth AG

115/139

Diagnostics

Summary of Contents for Rexroth IndraControl S67 Series















































































































































Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Related manuals for Rexroth IndraControl S67 Series

Brands by name

Popular brands

Bosch Rexroth IndraControl S67 Series, Application Description

Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Related manuals for Rexroth IndraControl S67 Series

Brands by name

Popular brands