Bosch Rexroth IndraControl S67 Series Application Description Download Page 70

Page: 70 / 142

Parameter number

Parameter description

IDN/S-0-0128

CP4 transition check
Description

Command for checking the configuration of

the slave before switching from CP3 to

CP4. Invalid IDN parameters are entered

in the IDN/S-0-0022 list

Data type, length Integer (binary), 16 bit
Write-protection

Never

Default value

–

Tab. 9-9:

Function group control (FG_Control)

Parameter number

Parameter description

IDN/S-0-0014

Interface status
Description

Status word for the current state of the

Sercos interface

Data type, length Integer (binary), 16 bit
Write-protection

always

Default value

–

IDN/S-0-1003

Allowed MST losses in CP3/CP4
Description

Maximum number for consecutive MST

failures (MDT0) in CP3 and CP4

Data type, length Integer (decimal), 32 bits
Write-protection

CP3, CP4

Default value

–

IDN/S-0-1026

Version of communication hardware
Description

Current version of the communication

hardware

Data type, length Text (ASCII), variable
Write-protection

always

Default value

"SERCON100S V04.08"

IDN/S-0-1035

Error counter Port1 and Port2
Description

Counter for faulty Sercos and standard

Ethernet telegrams on port 1 and port 2

Data type, length Integer (hexadecimal), 32 bit
Write-protection

Never

Default value

Bosch Rexroth AG

DOK-CONTRL-S67S3BKDI8*-AP03-EN-P

Rexroth IndraControl S67 Sercos Coupler 8 Digital Inputs (M8)

68/139

Sercos

Summary of Contents for Rexroth IndraControl S67 Series















































































































































Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Related manuals for Rexroth IndraControl S67 Series

Brands by name

Popular brands

Bosch Rexroth IndraControl S67 Series, Application Description

Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Related manuals for Rexroth IndraControl S67 Series

Brands by name

Popular brands