Bosch DIVAR DIP-7080-00N Installation Manual Download Page 65

Page: 65 / 72

Two (2) USB ports on the rear IO panel

Four (4) USB header connectors for front access

One (1) Type A internal connector

Keyboard/Mouse

PS/2 Keyboard/Mouse ports on the I/O backplane

Serial (COM) Ports

Two (2) Fast UART 16550 Connections: one 9-pin RS-232 port
and one header

Super I/O

Winbond Super I/O 83627DHG-P

BIOS

32 Mb SPI AMI BIOS SM Flash BIOS

DMI 2.3, PCI 2.3, ACPI 1.0/2.0/3.0, USB Keyboard and SMBIOS
2.5

Power Configuration

ACPI/ACPM Power Management

Main switch override mechanism

Keyboard Wake-up from Soft-Off

Internal/External moder ring-on

Power-on mode for AC power recovery

PC Health Monitoring

CPU Monitoring

Onboard voltage monitors for CPU core, +3.3V, +5V, +/-12V,
+3.3V Stdby, +5V Stdby, VBAT, HT, Memory, Chipset

CPU 3-Phase switching voltage regulator

CPU/System overheat LED and control

CPU Thermal Trip support

Thermal Monitor 2 (TM2) support

Fan Control

Fan status monitoring with firmware 4-pin (Pulse Width
Modulation) fan speed control

Low noise fan speed control

System Management

PECI (Platform Environment Configuration Interface) 2.0
support

System resource alert via Supero Doctor III

SuperoDoctor III, Watch Dog, NMI

Chassis Intrusion Header and Detection

CD Utilities

BIOS flash upgrade utility

DIVAR IP 7000 2U

Appendices | en

Bosch Sicherheitssysteme GmbH

Installation Manual

2013.09 | V2 | DOC

Summary of Contents for DIVAR DIP-7080-00N









































































Search results

Summary of Contents for DIVAR DIP-7080-00N

Reviews:

Related manuals for DIVAR DIP-7080-00N

Brands by name

Popular brands

Bosch DIVAR DIP-7080-00N, Installation Manual

Search results

Summary of Contents for DIVAR DIP-7080-00N

Reviews:

Related manuals for DIVAR DIP-7080-00N

Brands by name

Popular brands