Bosch DIVAR DIP-7080-00N Installation Manual Download Page 14

Page: 14 / 72

Chassis setup and maintenance

This chapter covers the steps required to install components and perform maintenance on the
chassis.

Caution!
Review the warnings and precautions listed in the manual before setting up or servicing this
chassis.

See also:
–

Safety precautions, page 5

–

Rack precautions, page 24

–

General system precautions, page 25

Removing the chassis cover

To remove the chassis cover:
1.

Remove the two screws on each side of the cover, which secure the cover to the chassis.

Press the release tabs to remove the cover from the locked position. Press both tabs at
the same time.

Once the top cover is released from the locked position, slide the cover toward the rear
of the chassis.

Lift the cover off the chassis.

Notice!
Except for short periods of time, do NOT operate the server without the cover in place. The
chassis cover must be in place to allow proper airflow and prevent overheating.

3.1

en | Chassis setup and maintenance

DIVAR IP 7000 2U

2013.09 | V2 | DOC

Installation Manual

Bosch Sicherheitssysteme GmbH

Summary of Contents for DIVAR DIP-7080-00N









































































Search results

Summary of Contents for DIVAR DIP-7080-00N

Reviews:

Related manuals for DIVAR DIP-7080-00N

Brands by name

Popular brands

Bosch DIVAR DIP-7080-00N, Installation Manual

Search results

Summary of Contents for DIVAR DIP-7080-00N

Reviews:

Related manuals for DIVAR DIP-7080-00N

Brands by name

Popular brands