18
Robert Bosch Hausgeräte GmbH
en
Loosen blade insert clockwise ( )
and remove from the blender jug.
Clean all parts, see “Cleaning and
servicing”.
Universal cutter
Use (depending on model):
– With the blade insert with blender/cutting
blade for cutting and chopping meat,
hard cheese, onions, herbs, garlic, fruit,
vegetables.
– With the blade insert with grinding blade
for grinding and cutting fairly small
quantities of spices (e.g. pepper, cumin,
juniper, cinnamon, dried anise, saffron),
grain (e.g. wheat, millet, linseeds), coffee
and sugar.
Fig. F shows guide values for the maximum
quantities and processing times when
working with the universal cutter.
Fig.
Put down universal cutter jug with the
opening face up.
Add food, which is to be cut, in the
jug.Note MAX mark on the jug!
Place seal on the blade insert. Ensure
that the seal is positioned correctly.
Insert blade insert ( / ) into the
universal cutter jug and lock anti-
clockwise ( ).
Turn universal cutter over (blade insert
face down).
Attach the universal cutter (arrow on jug
on dot on the appliance) and rotate all the
way clockwise.
Insert the mains plug.
Set the rotary switch to the desired
setting.
Note: The longer the appliance remains
switched on, the finer the ingredients are cut.
Recommendations on using the accessories
can be found in the section “Recipes/
Ingredients/Processing”.
After using the appliance
Set the rotary switch to 0/off.
Remove mains plug.
Rotate universal cutter anti-clockwise and
remove.
Turn universal cutter over (blade insert
face up).
Loosen blade insert clockwise ( ) and
remove from the universal cutter jug.
Empty jug.
Clean all parts, see “Cleaning and
servicing”.
Cleaning and servicing
The appliance requires no maintenance.
Thorough cleaning protects the appliance
from damage and keeps it functional.
An overview of cleaning the individual parts
can be found in Fig.
.
Warning!
Surfaces may be damaged. Do not use
abrasive cleaning agents.
Note: If processing e.g. carrots and red
cabbage, the plastic parts will become
discoloured by a red film which can be
removed with a few drops of cooking oil.
Cleaning the base unit
Remove mains plug.
Wipe the base unit with a damp cloth. If
required, use a little detergent.
Then dry the base unit.
Cleaning the bowl and accessories
m
Risk of injury from sharp blades/
rotating drive!
Do not remove/attach the universal cutter
until the drive has stopped.
Do not touch blades of the blade insert
with bare hands. Clean them with a brush.
Important information
If the seal is damaged or not correctly
positioned, liquid may run out.
m
Risk of electric shock!
Never immerse the base unit in water or
place under running water.
m
Risk of injury from sharp blades!
Do not touch blades of the universal blade
with bare hands. Clean them with a brush.
Do not grip the sharp blades or edges of
the cutting discs. Take hold of discs by the
edge only!
MCM3_alle.book Seite 18 Donnerstag, 12. Februar 2015 4:40 16
Robert Bosch Hausgeräte GmbH
19
en
All parts are dishwasher-proof.
Do not wedge plastic parts in the dishwasher
as they could warp.
Cleaning the blender/universal cutter
The blender jug (without blade insert), lid and
funnel are dishwasher-proof.
Do not clean the blade insert in the dish-
washer, but under running water (do not soak
in water). Remove seal for cleaning.
Troubleshooting
Fault:
Appliance does not start or appliance switches
off during operation.
Possible cause:
Bowl or lid or the accessory has not been
attached correctly or has become detached.
Remedial action:
Set the rotary switch to 0/off.
Correctly attach bowl/lid or accessory and
screw on all the way.
Switch the appliance on again.
Storage
Fig.
The tools can be stored in the bowl to save
space.
Recipes/Ingredients/Processing
m
Risk of injury from sharp blades!
Do not touch blades of the blade insert
with bare hands. When not in use, always
store the universal blade in the blade
guard. Clean them with a brush.
m
Risk of injury!
Before rectifying a fault, pull out the mains
plug.
Important information
If the fault cannot be eliminated, please
contact customer service (see customer
service addresses at the end of this
booklet).
Tool
Speed
Time
Recipes/Ingredients/Processing
or
low
approx.
1–2 min
Yeast dough
Max. 500 g flour
25 g yeast or 1 packet of dried yeast
220 ml milk
1 egg
1 pinch of salt
80 g sugar
60 g butter
Graded rind of half a lemon
Add all ingredients (except the milk) to the bowl.
Set rotary switch to a low speed for 10 seconds.
Add milk and stir at low speed for about 1½ minutes.
Ingredients should be at the same temperature. When the dough
has a smooth appearance, place in a warm location.
M
Onions, garlic
Amount: from 1 onion, quartered, up to 300 g
from 1 clove of garlic up to 300 g
Process the onion/garlic until it has been chopped to the
required size.
high
Parsley
Amount: from 0 g up to 50 g
Process the onion/garlic until it has been chopped to the
required size.
MCM3_alle.book Seite 19 Donnerstag, 12. Februar 2015 4:40 16
19
