manualshive.com logo in svg

BOS Suspension Deville 35, Service Manual

Share
Download
BOS Suspension Deville 35 Service Manual Download Page 37

  

 

 

35 

 SM_151815_rev00 

Service Manual DEVILLE 35 since year 2017

 

 

8

 

Additional Information 

8.1

 

AIR SETTINGS 

Weight (Kg/lbs.) 

55/120  65/143  75/165  85/187  95/210  105/132 

Air pressure (psi) 

43 

54 

61 

67 

72 

75 

 

8.2

 

HYDRAULIC SETTINGS 

 

To start setting your fork, turn clockwise completely the knobs (=click 0). Then turn counterclockwise one click at a 
time.

 

Basic click: 
 
Low-speed compression: 10 clicks 

 

High-speed compression: 10 clicks 

 

Rebound: 14 clicks 

 

 

8.3

 

F.A.Q. 

My fork loses pressure when I remove the pump, what can I do?  
Check the valve core tightness using a Schrader valve core tool.  
 
My fork has negative travel, is this normal?  
The BOS air spring is designed to lower the engagement threshold as much as possible. Therefore, it is possible on some 
bikes that there will be a small negative travel.  
 
Where can I buy original stickers or a valve cap?  
These items and more are available in our online store.  
 
My fork has bushing play from new, what should I do?  
The unique bushing alignment  and tolerance on BOS forks results in less  friction, more  sensitivity, and some bushing 
play  from  new.  If  the  bushing  play  feels  abnormally  excessive,  please  contact  a  BOS  certified  service  center  for 
expertise.  
 
My fork is lowering as I deflate it, what is happening?  
When  you  deflate  the  fork  by  the  Schrader  valve,  you  are  only  emptying  the  positive  air  chamber.  The  negative  air 
chamber  stays  under  pressure  and  exerts  an  opposing  force  on  the  air  piston  and  pulls  the  fork  down.  To  avoid  this 
phenomenon, deflate the fork in steps of 30-40 PSI and equalize the air chambers between steps (compress and release 
the fork 5-10 times over the first 20mm – 1 inch) of travel.  
 
I just inflated my fork for the first time and it is really hard, what can I do?  
Have you  equalized your fork’s air  chambers? If not, check  how it’s done in the setup  section of your product’s user 
manual.  
Did you change your fork’s settings? Check that your low-speed and high-speed compression are at our recommended 
base settings given in the setup section of your product’s user manual.  

Summary of Contents for Deville 35







































Reviews:

No comments

Brands by name

Popular brands

Load more brands