manualshive.com logo in svg

BOS Suspension Deville 35, Service Manual

Share
Download
BOS Suspension Deville 35 Service Manual Download Page 21

  

 

 

19 

 SM_151815_rev00 

Service Manual DEVILLE 35 since year 2017

 

1 

 

 

2 

 

 

3 

 

 

6.3

 

SLIDE BUSHINGS REPLACEMENT 

 

 

 

 
Place the fork on the vise block. 
Rotate the fork at 45° in front of you. 

 

 

 

 

Tool(s) required : 
 
-

 

BOS suspension vise block / ref. 151815-O-012 

 

 

Take the slide bushing extractor tool. 
This tool is used for DEVILLE and DIZZY models. Locate the DEVILLE side.  
Unscrew the middle nut to push it away from the DEVILLE side. 

Place the aluminum brace on the tool. 

 

 

 

 

Tool(s) required : 

 
-

 

BOS slide bushing extractor / ref. 150707-SE-003A 

 

 
Place the washer parallel to the ground. 
Push the tool inside the casting until the washer is under the lower bushing. 

Once the washer is located under the lower bushing, pull back on the tool. 
The washer will then be locked under the lower bushing. 
Keep traction on the tool while screwing the nut until it touch the tool. 

 

 

 

 

Tool(s) required : 
 

-

 

BOS slide bushing extractor / ref. 150707-SE-003A 

 

1 

2 

1 

Summary of Contents for Deville 35







































Reviews:

No comments

Brands by name

Popular brands

Load more brands