manualshive.com logo in svg

BOS Suspension Deville 35, Service Manual

Share
Download
BOS Suspension Deville 35 Service Manual Download Page 23

  

 

 

21 

 SM_151815_rev00 

Service Manual DEVILLE 35 since year 2017

 

7 

 

 

8 

 

 

9 

 

 

 

 

 

 
Clean the tool and throw away the old bushings 
Clean the casting: 

-

 

Oil fountain with brush + bottlebrush 

OR (if not equipped): 

-

 

Isopropyl a brush + bottlebrush 

 

 

 

 

Tool(s) required : 
 

-

 

Oil fountain with brush 

-

 

Bottlebrush 

-

 

Oil type WD40 

 

 

 
Lower slide bushing are thinner than upper slide bushings. 

Take lower slide bushing and orient its joint inside the fork. 
Drop it inside the casting. 

Do the same for the other lower slide bushing. 

 

 

 

 

Tool(s) required : 

 

-

 

n/a (by hand) 

 

 

 

Take the lower slide bushing tool and insert it inside the casting. 
Place the strike tip on the tool. 
Hit the tool with the rubber mallet to insert the bushing. 

Stop to strike the tool once it touch the casting. 
Repeat these operations for the other side of the casting. 

 

 

 

 

Tool(s) required : 
 
-

 

BOS lower slide bushing tool / ref.  151815-O-001  

-

 

Rubber mallet 

 

Upper 

slide 

bushing 

Lower 

slide 

bushing 

1 

Joint 

inside 

2 

1 

2 

Summary of Contents for Deville 35







































Reviews:

No comments

Brands by name

Popular brands

Load more brands