BodyCraft GL Owner'S Manual Download Page 9

Page: 9 / 21

STEP 3

ASSEMBLE SEAT SUPPORT FRAME

AND SEAT & BACK PAD

1. Attach

SEAT SUPPORT FRAME (8)

FRONT UPRIGHT (3)

, using three

3/8" X 3"

HEX HEAD BOLTS (82)

six

3/8" WASHERS (100)

and three

3/8" NYLA-NUTS

(104)

Tighten

2. Attach the

SEAT BACK ADJUSTER (11)

to the

FRONT UPRIGHT (3)

using one

3/8" X 5-1/2" HEX HEAD BOLT (78)

, two

3/8" WASHERS (163)

and one

3/8"

NYLA-NUT (170)

. Tighten this bolt until there is no play in the

SEAT BACK

ADJUSTER (11)

NOTE:

If it does not pivot freely, loosen slightly.

3. Attach

LEG HOLDER (16)

SEAT BACK ADJUSTER (11)

, using two

5/16" X 1/2"

BUTTON HEAD BOLT (88)

and two

5/16" LARGER WASHERS (101)

. Tighten

these screws.

4. Slide the two

METAL HINGES (21)

, holes at bottom, onto the axle welded to the top

of the

SEAT BACK ADJUSTER (11)

, then attach the

BACK PAD (51)

to the

METAL

HINGES (21)

using four

3/8" X 1" HEX THREADED BOLTS (86)

, and four

3/8"

WASHERS (100)

Tighten

5. Insert a

1" X 2" END CAP (56)

into each end of the

SEAT ADJ. FRAME (7)

and

then slide the

SEAT ADJ. FRAME (7)

into the

SEAT SUPPORT FRAME (8)

. The

SEAT ADJ. FRAME (7)

is held in place by a

LOCKING

SPRING KNOB (71)

6. Attach

LEG EXTENSION ARM (9)

SEAT SUPPORT FRAME (8)

, by inserting

LEG EXTENSION AXLE (27)

. Fasten

LEG EXTENSION AXLE (27)

using two

5/16"

X 5/8" BUTTON HEAD BOLTS (89)

, two

5/16" SPRING WASHERS (102)

, and two

5/16" LARGER WASHERS (101)

Tighten

7. Insert and center

1" FOAM ROLLER HOLDER (25)

into the

SEAT ADJ. FRAME (7)

and another into the

LEG EXTENSTION ARM (9)

. Tighten

5/16" X 1/4" SET

SCREW (94)

in both.

8. On the two

FOAM ROLLER HOLDERS (25)

and the

LEG HOLDER (16)

slide

PLASTIC ROLLER CAP (60)

(domed side first) and a

FOAM ROLLER PAD (59)

onto each side and secure with a

PLASTIC ROLLER CAP (60)

and

5/16"

SMALLER WASHER (106)

and

5/16" X 1-1/4" ROUND HEAD ALLEN BOLT (92)

on each side as shown.

Tighten.

NOTE:

The Washer goes in between the

PLASTIC ROLLER CAP (60)

and

FOAM ROLLER HOLDER (25)

LEG HOLDER

(16)

as shown.

TIP!

TO EASE THE ASSEMBLY PROCESS, spray window cleaner

or water into the holes of the

FOAM ROLLER PADS (42)

before

sliding onto shafts.

1/4

1/2

3/4

1/4

1/2

3/4

1/4

1/2

3/4

1/4

1/2

3/4

1/4

1/2

3/4

1/4

1/2

3/4

(inch)

Summary of Contents for GL






















Search results

Summary of Contents for GL

Reviews:

Related manuals for GL

Brands by name

Popular brands

BodyCraft GL, Owner'S Manual

Search results

Summary of Contents for GL

Reviews:

Related manuals for GL

Brands by name

Popular brands