BodyCraft GL Owner'S Manual Download

Page: 2 / 21

Congratulations and Thank You!

Important Safety Notes

QUESTIONS?

Thank you for selecting the

Bodycraft GL/GLX Strength Training System

The Bodycraft GL/GLX offers an impressive array of strength training

exercises to develop every major muscle group of the body. Whether your

goal is cardiovascular fitness, a shapely, toned body or dramatic muscle size

and strength, the Bodycraft GL/GLX will help you achieve the results you want.

For your safety and benefit, read this manual and the accompanying literature

before using the Bodycraft GL/GLX. Keep this manual for future reference.

If you have additional questions, please call your local Bodycraft GL/GLX

Dealer or our

customer service department

at 800-990-5556

Monday through

Friday, 9 am until 5 pm Eastern Standard Time.

There is a risk assumed by individuals who use this type of equipment.

Before beginning this or any other exercise program consult your physician.

This is especially important for individuals over the age of 35 or persons

with preexisting health problems. Recreation Supply, Inc. assumes no

responsibility for personal injury or property damage sustained by or

through use of this product.

1. This product must be assembled on a flat, level surface to assure its proper function.

2. Clean pads and frame on a regular basis. We recommend warm, soapy water.

Do not use harsh or abrasive chemicals.

3. Inspect and tighten all parts before every use. Replace any worn

parts immediately. Failure to do so may result in serious injury.

4. Keep children away from the BODYCRAFT GLX at all times.

5. Keep your hands away from cables and pulleys during operation.

6. Keep your hands away from moving parts other than the designated handles.

7. When adjusting the seat, make sure the spring pin is fully engaged.

If not, the seat may slip and cause serious injury.

8. Make certain all cables are seated within the pulleys before every use.

9. Exercise with care to avoid injury.

10. If you are unsure about the proper use of the BODYCRAFT GL/GLX strength training

system call your local BODYCRAFT dealer or our customer service department.

As a quality home gym supplier we are committed to your complete satisfaction.

If you have questions, or find missing or damaged parts, we will guarantee your

complete satisfaction through our authorized dealer service centers or our home

office customer service department. Please call your local dealer for assistance

BODYCRAFT

at 800-990-5556 (9 AM - 5 PM) EST. Our trained technicians

will provide immediate assistance to you, free of charge.

Summary of Contents for GL






















Search results

Summary of Contents for GL

Reviews:

Related manuals for GL

Brands by name

Popular brands

BodyCraft GL, Owner'S Manual

Search results

Summary of Contents for GL

Reviews:

Related manuals for GL

Brands by name

Popular brands