BodyCraft GL Owner'S Manual Download Page 3

Page: 3 / 21

Gym Placement Planner

The dimensions below below are based on installing the gym into a corner of your workout room.

Important Notes and Tips:

Ratchet

9/16" Socket

3/4" Socket

9/16" Combination Wrench

3/4" Combination Wrench

Adjustable Wrench

Rubber Mallet

Metric Allen Key Set

Silicone Spray

Window Cleaner or Water

Recommended Tools

for Assembly

1. Do not tighten any bolts until instructed.

2. Two people are reguired for the safe assembly

of the gym.

3. Use window cleaner or water to assist with roller

pad installation.

4. Use silicone lubricant on guide rods prior to weight

plate installation.

5. Carefully install plastic caps using a rubber mallet.

6. When measuring bolt lengths, only measure the shank.

i.e. 2-1/4" Hex Bolt

1/4

1/2

3/4

1/4

1/2

3/4

1/4

1/2

3/4

1/4

HEIGHT

83"

GL 45"

GLX 54"

GL/

GLX

52.5"

GL/

GLX

77"

GL 65"

GLX 74"

HEIGHT

83"

GL/GLX Dimensions

GL/GLX w/Leg Press

Option Dimensions

Summary of Contents for GL






















Search results

Summary of Contents for GL

Reviews:

Related manuals for GL

Brands by name

Popular brands

BodyCraft GL, Owner'S Manual

Search results

Summary of Contents for GL

Reviews:

Related manuals for GL

Brands by name

Popular brands