manualshive.com logo in svg

Blue-White FLEXFLO A4 Series, Operating Manual, Page: 45 / 64

Share
Download
Blue-White FLEXFLO A4 Series Operating Manual Download Page 45

To Input a Language:

1

Open the 

App Drawer

2

Open 

Settings

3

Open 

System

4

Select 

Locale

5

Select 

Desired Language

!

English

!

Deutch

!

Español

!

Français

!

Portugues

6

Confirm by pressing 

OK

12.5  Set Language

This setting is used to change the system language.

® 

 

FLEXFLO A4

12.0  Settings

Page 44

Page 45

® 

 

FLEXFLO A4

12.0  Settings

12.6  Pump Rotation Direction

This setting is used to change the rotational direction of pump. In most applications, the 
tube will fail by developing a small leak in the outlet side (pressure side) of the tube 
assembly. By reversing the roller rotation, the wear point in the tube is moved to the 
opposite side to the pump tube assembly, increasing the life of the tube.

Important!

 Changing the rotational direction of the pump reverses the inlet & outlet 

sides. 

IMPORTANT! Swap sides of the suction (inlet) and discharge (outlet) tubing/piping. There is no need to remove 
the pump head cover.

NOTE: The pump tube will form a natural U-shaped curve. Do not attempt to install the pump tube against the 
natural U-shape direction as damage to the tube can result.

To Change The Direction Of The Pump Rotation

1

Open the 

App Drawer

2

Open 

Settings

3

Open 

System

4

Select 

Pump Direction

5

Select 

Desired Rotation

 

!

Clockwise 

!

Counter Clockwise

6

Confirm by pressing 

OK

Summary of Contents for FLEXFLO A4 Series

































































Reviews:

No comments