Blue-White FLEXFLO A4 Series Operating Manual Download Page 4 | Manualshive

Page: 4 / 64

Blue-White FLEXFLO A4 Series Operating Manual Download Page 4

®

Congratulations on purchasing the A4 FLEXFLO variable speed Peristaltic
Metering Pump.

®

Your FLEXFLO A4 pump is pre-configured for the tubing that shipped with your
metering pump. The tubing assembly has an Identification number printed for
easy re-order.

Please Note:

Your new pump has been pressure tested at the factory with

clean water before shipping. You may notice trace amounts of clean water in the
pre-installed tube assembly. This is part of our stringent quality assurance pro-
gram at Blue-White Industries.

For more information please visit us at:

ww.blue-white.com

For videos and tutorials please visit as at:

https://www.blue-white.com/resources/videos

Page 4

®

FLEXFLO A4

1.0 Introduction

1.1

What’s In The Box

The following items are included with every A4 peristaltic metering pump:

Page 5

®

FLEXFLO A4

1.0

Introduction

A4 Peristaltic Pump

USB Flash Drive With Instruction Manual

Standard Mounting Brackets

Spare Tubing

Tube Installation Tool

Injection Fitting

Suction Tubing

Discharge Tubing

Suction Strainer

«
...
2
3
4
5
6
...
»

Summary of Contents for FLEXFLO A4 Series

































































Reviews:

No comments