manualshive.com logo in svg

Blue-White FLEXFLO A4 Series, Operating Manual, Page: 37 / 64

Share
Download
Blue-White FLEXFLO A4 Series Operating Manual Download Page 37

To Enable Modbus TCP:

1

Open the 

App Drawer

2

Select 

Industrial Protocols

3

Select 

Modbus TCP/IP

4

Pump will go to home screen

5

Select 

Settings

 to input:

!

IP Address 

!

Subnet Mask

!

Gateway

!

Always on

6

Confirm by pressing 

Save

10.4  Modbus TCP/IP

This is used to configure the Modbus TCP/IP

Three values to be defined: 

1) IP Address 
2) Subnet Mask 
3) Gateway 
4) Always on

® 

 

FLEXFLO A4

10.0  Industrial Protocols

Page 36

Page 37

® 

 

FLEXFLO A4

10.0  Industrial Protocols

To Enable Profibus:

1

Open the 

App Drawer

2

Select 

Industrial Protocols

3

Select 

Profibus

4

Pump will go to home screen

5

Select 

Settings

 to input:

!

IP Address 

!

Subnet Mask

!

Gateway

6

Confirm by pressing 

Save

10.5  Profibus

This is used to configure the Profibus

Three values to be defined: 

1) IP Address 
2) Subnet Mask 
3) Gateway
4) Always on

Summary of Contents for FLEXFLO A4 Series

































































Reviews:

No comments