background image

2

AQT-RCS

Instruction Manual

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE

NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV System Installer’s attention to Article 820-40 of the NEC that  

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be  

connected to the grounding system of the building, as close to the point of cable entry as practical.

For all pluggable equipment the socket-outlet shall be  

installed near the equipment and shall be easily accessible.

!

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The  lightning  flash  with  arrow-

head  symbol  within  an  equilateral  

triangle  is  intended  to  alert  you 

to  the  presence  of  uninsulated  

“dangerous  voltage”  within  the 

product’s  enclosure  that  may  be 

of  sufficient  magnitude  to  consti-

tute  a  risk  of  electrical  shock  to  

persons.

The exclamation point within an 

equilateral  triangle  is  intended 

to  alert  you  to  the  presence  of  

important  operating  and  main-

tenance  (servicing)  instructions  

in  the  literature  accompanying 

the product.

TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER FROM THIS UNIT.   

NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Unpacking and Installation

NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV System Installer's at ten tion to Article 820-40 of the NEC that provides guidelines for 
proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, 
as close to the point of cable entry as practical.

Unpacking and Handling

Each unit is shipped with all equip ment assembled, wired, factory tested, and then packaged in an appropriate shipping container. 
Ensure that all accessories are removed from the container and packing material before they are discarded.

Mechanical Inspection

Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is clean, and no wires, cables, or 
connectors are broken, damaged or loose.

Precautions

Adherence  to  the  initial  installation  precautions  outlined  in  the  Table  below  will  help  prevent  problems  arising  during  the 
installation and future maintenance of the unit.

Damage in Shipment

Should any damage be discovered after unpacking the unit, immediately file a claim with the carrier. A full report of the damage 
shall be made and a copy forwarded to Blonder Tongue Laboratories Inc. The company will then advise what disposition is to be 
made of the equipment.

Summary of Contents for AQT-RCS





















Reviews: