Black Box LRA2900A Page 20 Getting Started Manual Download | Manualshive

Page: 20 / 66

background image

Approvals

20

Model LRA2900A RAS Getting Started Guide

1 • Introduction

•

ETHERNET: Green if link status is nominal for the Ethernet port.

•

CALLS ACT: Green to indicate call activity on the Model LRA2900A.

•

WAN STATUS: Green indicates normal status at each of the four T1/E1/PRI links. Red indicates an error.

Approvals

The Model LRA2900A RAS has achieved the following approvals:

•

FCC Part 15, Class A

•

FCC Part 15, Class B

•

FCC Part 68

•

Complies with UL1950 (MET)

•

Canadian cMET

•

Canadian CS-03

•

EMC Directive 89/336/EEC

•

Low Voltage Directive 73/23/EEC (EN60950)

•

ITU-T CTR-4 and CTR-12

«
...
18
19
20
21
22
...
»

Summary of Contents for LRA2900A



































































Reviews:

No comments

Related manuals for LRA2900A

Brand: Lantronix Pages: 6

Brand: Lantronix Pages: 27

Brand: ExtraHop Pages: 5

AirborneDirect ABDG-SE-IN5410

Brand: Quatech Pages: 8

Portbase PB-3010

Brand: SystemBase Pages: 45

Brand: Buffalo Pages: 2

Brand: Seyeon Pages: 10

Brand: FS Pages: 91

Brand: NEC Pages: 10

Brand: NEC Pages: 20

Brand: NEC Pages: 2

Brand: NEC Pages: 18

Brand: NEC Pages: 2

Care Standard/300

Brand: NEC Pages: 11

Brand: NEC Pages: 88

Brand: NEC Pages: 89

Brand: NEC Pages: 62

Express 5800/120Ed

Brand: NEC Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands