Black Box LRA2900A Page 49 Getting Started Manual Download

Page: 49 / 66

3 • Configuring the RAS for operation

Model LRA2900A RAS Getting Started Guide

Completing the installation

To save the displayed data as a text file, select the

Save

option on your browser (see figure 34). For example,

under Netscape, select

File

Save As

. A dialog box will display enabling you to save the contents of the export

parameters to a text file. Select the location where you want the file stored, type a file name, and click

Save

Figure 34. Saving the access server flash memory configuration data as a text file

Completing the installation

This section verifies that the RAS is fully operational.

1. Temporarily disconnect the male ends of both power cords from the power outlet. Wait 30 seconds, then

plug the power cords in again.

2. Verify that the green POWER LED is lit. If the POWER LED is flashing green, refer to Chapter 5, “Trou-

bleshooting and maintenance”.

3. Verify that the Link 1 Frame LED illuminates, indicating that the RAS is synchronizing with the T1/E1/

PRI signal.

4. Verify that after 5 seconds, the Link A Error LED begins flashing, indicating that the RAS is satisfied with

the quality of the T1/E1/PRI signal.

5. Verify that after 10 seconds, the Link A Error LED extinguishes, indicating that the RAS is satisfied with

the network signal and that the link is ready for use.

Summary of Contents for LRA2900A


































































Search results

Summary of Contents for LRA2900A

Reviews:

Related manuals for LRA2900A

Brands by name

Popular brands

Black Box LRA2900A, Getting Started Manual

Search results

Summary of Contents for LRA2900A

Reviews:

Related manuals for LRA2900A

Brands by name

Popular brands