Black Box LRA2900A Page 19 Getting Started Manual Download | Manualshive

Page: 19 / 66

background image

1 • Introduction

Model LRA2900A RAS Getting Started Guide

19

Hardware overview

•

Support for MIB-II (RFC-1213), DS1 MIB (RFC-1406), RIPv2 MIB (RFC 1389), Ethernet MIB (RFC-
1643), Frame Relay DTE MIB (RFC-1315) and Black Box’s enterprise MIB (1768)

•

System logging to configuration port, non-volatile FLASH, volatile RAM, SYSLOG Daemon, and
SNMP trap

•

RADIUS Accounting

•

Dial-in dynamic IP address pool management

•

User configurable login prompts and banners

•

Status reporting of all access server parameters

•

Built in HTTP server for complete configuration and control using a standard Web browser

Figure 4. Model LRA2900A front panel LEDs

LED display

The front panel (see figure 4) includes LEDs for:

•

POWER: Green if power is being applied. Flashing if a power supply has failed.

•

CPU FAIL: Red if the CPU has failed.

•

ALARM: Red if the Model LRA2900A is in an alarm state.

•

SYSTEM: Green if the RAS is operating normally.

CA

LL

A

CT

NO SIGNAL

«
...
17
18
19
20
21
...
»

Summary of Contents for LRA2900A



































































Reviews:

No comments

Related manuals for LRA2900A

Brand: G-Technology Pages: 35

Brand: Qlogic Pages: 20

Brand: TP-Link Pages: 16

SUPERSERVER 5017C-MF

Brand: Supero Pages: 96

Brand: Autonomic Pages: 17

Force10 MXL Blade

Brand: Dell Pages: 2

Brand: Asus Pages: 150

RS300-E6 Series

Brand: Asus Pages: 162

RS161-E5 - 0 MB RAM

Brand: Asus Pages: 124

Brand: Asus Pages: 126

Brand: Asus Pages: 182

Brand: Asus Pages: 164

Brand: Asus Pages: 178

RS120-E4 - 0 MB RAM

Brand: Asus Pages: 174

Brand: Asus Pages: 176

RS520-E8-RS12-E

Brand: Asus Pages: 202

Brand: Asus Pages: 194

Brand: Asus Pages: 196

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands