Birmingham WSG1640AHD Operating Manual Download

Page: 39 / 85

Operating Manual

Auto down feed stop and reset

while the autodown feed program is going, stop the working table by

speed control lever , the table and wheel head move stop, restart the

workig table longitudinal moving, the program resatart too.

While the autodown feed program is going, turn the knob SA4 to “jog

feed”

position, the program is stop, and then the operator can

make grinding head down feed by SB6 , and if turn SA4 to “auto down

feed” mode again, push the button SB6 , the program will going on

again.

While the auto down feed program is going, push soft KEY F8, the

program will be cancel, and the grind head will lift up auto.

NOTE: WHEN USE THE PLUNGE GRINDING, MUST NOT MOVE THE

SADDLE AVOID WHEEL BROKEN AND THE CHIP ON HIGH SPEED

WILL DAMAGE THE PEOPLE!

Must not press the KEY F11 OR F15 by mistake while the auto.

down feed working in process

5. how to use the HMI

F16

F15

F14

F13

F12

F11

F10

ESC

ENTER

SHIFT

TD400C

SIEMENS

Summary of Contents for WSG1640AHD






















































































Search results

Summary of Contents for WSG1640AHD

Reviews:

Related manuals for WSG1640AHD

Brands by name

Popular brands

Birmingham WSG1640AHD, Operating Manual

Search results

Summary of Contents for WSG1640AHD

Reviews:

Related manuals for WSG1640AHD

Brands by name

Popular brands