BIOPAC Systems MP35 Hardware Manual Download

Page: 134 / 157

[email protected]

[email protected]

www.biopac.com

BIOPAC Hardware |

NIBP Systems

| Page 3 - 8

Updated: 6.7.2013

ANIMAL PREPARATION

Optional

Heating Chamber

Restrainer Animal Holders

Tail Cuff/Sensor

Turn the Animal Heating Chamber on.

Set the temperature value (press and hold P.Set and then press the up or
down arrow to reach the desired value).



For accurate noninvasive blood pressure measurement, the animal or
its tail should be warmed to 32°C.

Press the Heater button to start heating to the selected temperature value.

Place the animal inside the RESTRAINER “Animal Holder” (select the suitable size for the animal
volume).



Leave the tail outside.



Adjust the length to obtain a position where the animal has limited movement.

Place the RESTRAINER (with the animal) in the heating section of the Animal Heating Chamber.

Wait approximately 30 minutes for the animal to reach the selected temperature.

Remove the RESTRAINER from the Animal Heating Chamber.

Connect the IRSENSOR to the tail of the animal inside the RESTRAINER.

Check if the sensor just fits to the tail. The sensor should be between the mid point of tail and tail end
(spinal column). To achieve this, a suitable sensor should be selected.

10.

Wait for the animal to relax and become inactive before starting measurements.

TIP

Before starting the experiment, to condition the animal, put the animal inside the holder several
times a day and repeat the heating each time.

HARDWARE GUIDE

Summary of Contents for MP35






























































































































































Search results

Summary of Contents for MP35

Reviews:

Related manuals for MP35

Brands by name

Popular brands

BIOPAC Systems MP35, Hardware Manual

Search results

Summary of Contents for MP35

Reviews:

Related manuals for MP35

Brands by name

Popular brands