background image

8

•  Always disconnect the battery(s), or other 12v source, before installation or performing any maintenance.
•  The ballast is supplied with a 6-foot, 2 wire, power cord and 5-foot lamp cord, the ballast must be located so the lamp is 

easily removed and does not put any tension on the lamp, which could cause damage to the lamp and/or quartz sleeve. 

All installed wiring should be protected from heat, wear points (abrading) or mechanical stress. Secure ballast using the 

mounting tabs located on the ballast body.

•  Wire ballast power cord as follows;
•  Brown wire - Positive (+) to protected (fuse or circuit breaker) 12v DC source.
•  Blue wire - Negative (-) to suitable chassis ground.
•  If there are any questions or concerns regarding the installation and/or wiring of the 12v system, consult a qualified 

installer.

8.  It is recommended, when the carbon filter is new, to flush out the system thoroughly prior to use. Turn on the system’s faucet 

and allow water to run for 10 minutes to flush the filter and system. 

Figure 4 - 

Bio-Logic

®

 

Pure Water Pack

TM

 - Install

9.  Plug ballast into an approved Ground Fault Circuit Interrupt (GFCI) receptacle. Where a 2-prong or unprotected  3-prong 

receptacle is encountered, it must be replaced by a properly grounded Ground Fault Circuit Interrupt (GFCI) receptacle. 

Installation must be in accordance with the National Electrical Code and any local codes and ordinances by a qualified 

electrician.

10.  Once the plumbing hook ups are made, it is a good practice to disinfect the “downstream” plumbing. This is done by 

introducing chlorine or other disinfectant solution directly into the purifier chamber, a 100-ppm of chlorine is suggested. With 

the disinfectant solution in the purifier chamber, turn the ultraviolet purifier on. Open the “downstream” outlet until order is 

noticed. Close the outlet and allow the disinfectant to remain in the plumbing for at least three (3) hours. Flush the plumbing 

with ultraviolet purified water; allow the water to run for several minutes before use, this will allow the ultraviolet lamp to 

reach its full germicidal output.

Summary of Contents for PURE WATER PACK BIO 1.5 PWP





















Reviews: