manualshive.com logo in svg

Biddle CA M-150-W-F, User'S And Installer'S Manual, Page: 58 / 60

Share
Download
Biddle CA M-150-W-F User'S And Installer'S Manual Download Page 58

S

ERVICE

C

OMFORT

 A

IR

 C

URTAIN

58

The control panel displays four numbers: these constitute the 

unit code. 

The first number starts blinking.

3. Press 

 or 

 to increase or decrease the number. 

4. Press the 

 key.

The second number starts blinking.

5. Repeat the previous two steps until you entered all num-

bers.

No number will be blinking any more. 

ê

6. Press down microswitch 

1

. 

The LED next to the microswitch will start blinking.

The unit code is now entered.

7. Reset the control panel (see section 

6.3.3

).

7.8

Composition of Biddle control cable

The control cable for Biddle units is different from standard 

modular telephone cables. 

The plugs are of the RJ-11 type but the sockets are ‘straight’ – 

at both ends of the cable, the core is connected to the same 

pin.

Table 7-1   

Colour codes of Biddle cables

P

IN

C

OLOUR

1

(not used)

2

black

3

red

4

green

5

yellow

6

(not used)

1

6

5

4

3

2

Summary of Contents for CA M-150-W-F





























































Reviews:

No comments