manualshive.com logo in svg

Biddle CA M-150-W-F, User'S And Installer'S Manual, Page: 17 / 60

Share
Download
Biddle CA M-150-W-F User'S And Installer'S Manual Download Page 17

U

SER

’

S

 

AND

 I

NSTALLER

’

S

 M

ANUAL

I

NSTALLATION

Version: 4.0 (23-08-2007)

17

Warning:

w

The wall socket must remain accessible after the 

installation of the unit to be able to disconnect the 

unit from the mains when maintenance work is to 

be performed.

2.6.2 Connecting electrically-heated models (CA E and 

CA H)

Danger:

d

Do not perform the connection work unless you 

are qualified to work with three-phase current.

Particulars

•

Connect the unit to the power supply with a 5-core cable 

(not supplied). The maximum load data is specified on the 

type plate (see section 

1.3.4

).

•

An isolation switch (not supplied) must be fitted between 

the unit and the power supply. This switch must:

-

be all-pole; 

-

have a minimum contact clearance of 3 mm;

-

be positioned at a maximum of 4 m from the left side 

of the unit.

Warning:

w

The unit must 

not

 be switchable using the power 

supply cable: use the control panel for that.

Warning:

w

The unit must be grounded.

Warning:

w

Connect the unit in accordance with the applicable 

local requirements.

1

2

3

N

contact clearance 

R

S

T

N

Summary of Contents for CA M-150-W-F





























































Reviews:

No comments