manualshive.com logo in svg

Biddle CA M-150-W-F, User'S And Installer'S Manual, Page: 52 / 60

Share
Download
Biddle CA M-150-W-F User'S And Installer'S Manual Download Page 52

F

AULTS

C

OMFORT

 A

IR

 C

URTAIN

52

6.5

Remedying faults without message

If you suspect a fault but no fault message is displayed:

1. Using section 

6.2

 check if you can easily resolve the 

problem yourself.

2. Try to resolve the problem using the below table. No tech-

nical expertise is needed for this.

P

ROBLEM

L

IKELY

 

CAUSE

W

HAT

 

TO

 

DO

The control panel 

works normally but 

the unit does not 

respond.

The unit is control-

led by a signal from 

an external control.

1.

Check if 

 or 

 is displayed in the control panel.

2.

Check the setting nos. 60, 61 and 76 at the installer’s 

level (see section 

4.5

).

The fans are dead.

1.

Check the transformer fuse.

2.

Check the wiring between the transformer and the 

fans (connectors X120 and X130).

3.

Replace the transformer.

The unit does not 

work, the display is 

blank, and the con-

trol panel LED is not 

lit.

The unit is dead.

1.

Check the power connections and wiring.

The connection 

between the control 

panel and the printed 

circuit board is not 

correct.

1.

Check the control cable.

2.

Check wiring between connector plate and printed 

circuit board (connectors X380 and X390).

The printed circuit 

board does not 

work: the LEDs on 

the printed circuit 

board are not lit.

1.

Check fuse F110.

2.

Check the power supply cable (connector X110).

3.

Replace the printed circuit board.

The control panel is 

defective.

1.

Check the control panel by connecting it to another 

unit with another cable.

Replace the control panel if it does not work.

One fan does not 

work.

The fan is dead or 

defective.

1.

Check the wiring of the fan.

2.

Check the transformer fuse.

3.

Replace the fan.

The fans do not 

operate at a certain 

strength.

The connection to 

the relevant tap is 

not correct.

1.

Check the transformer connections.

2.

Check connector X130.

Summary of Contents for CA M-150-W-F





























































Reviews:

No comments