manualshive.com logo in svg

Biddle CA M-150-W-F, User'S And Installer'S Manual, Page: 46 / 60

Share
Download
Biddle CA M-150-W-F User'S And Installer'S Manual Download Page 46

F

AULTS

C

OMFORT

 A

IR

 C

URTAIN

46

6

.  .   Faults

6.1

Safety instructions

Danger:

d

Work on the unit’s interior shall be performed by 

qualified technical staff only.

Warning:

w

Before opening the unit, follow the safety instruc-

tions in section 

1.4

.

6.2

Resolving simple problems

If you suspect a fault, first try to resolve the problem using the 

below table. You need not be an expert for this.

P

ROBLEM

L

IKELY

 

CAUSE

W

HAT

 

TO

 

DO

The unit does not work, and the 

control panel display is blank.

If the LED is lit:

 the unit is in pause 

mode.

Exit the pause mode by pressing 

the  

key.

If the LED is not lit:

 no power is 

supplied to the control panel.

Check the power supply:

• plug in power point;

• isolation switch;

• unit  live.

One or more keys do not work.

If the display only shows the room 

temperature:

 the air curtain is 

switched off.

Switch the air curtain On using 

the  

key.

If the display reads 

 or 

:

 the 

unit is controlled by an external 

control.

This is not a fault. Operation is 

limited by the input signal from 

the external control.

The air curtain is switched Off 

but is still working.

Only electrically-heated models: 

unit 

is cooling down automatically.

This is not a fault. Normally, the 

unit will automatically shut down 

within 10 minutes.

The unit blows out cold air 

(without fault message).

If the display does not read the   

symbol:

 heating is disabled.

Enable heating using the 

 key.

Summary of Contents for CA M-150-W-F





























































Reviews:

No comments