manualshive.com logo in svg

Biddle CA M-150-W-F, User'S And Installer'S Manual, Page: 19 / 60

Share
Download
Biddle CA M-150-W-F User'S And Installer'S Manual Download Page 19

U

SER

’

S

 

AND

 I

NSTALLER

’

S

 M

ANUAL

I

NSTALLATION

Version: 4.0 (23-08-2007)

19

2.7

Installing control panel and external controls

2.7.1 Control panel details

Positioning

•

You may fix the control panel either to the wall or to a 

standard socket.

Cabling

Note:

n

Take the following into account, otherwise faults may 

occur:

-

The control cable between the control panel and the 

(first) connected unit may not be longer than 50 m.

-

Keep control cables away from electromagnetic fields 

and interference sources such as high-voltage cables 

and fluorescent-light starters.

-

Stretch control cables out or roll them up neatly.

-

Do not remove the dummy plug, unless otherwise 

stated.

Note:

n

Use only control cables from Biddle. Standard modular 

telephone cable is 

not

 suitable.

Multiple units operated from one single control panel

•

Up to 10 units can be connected to one single control 

panel. To do so, the units must be interlinked.

•

Only units that have the same unit code (see “code” on 

the type plate, section 

1.3.4

) can be operated from one 

control panel at the same time.

•

The total length of the control cables is not to exceed 

100 m.

2.7.2 External control details

Control panel input

The control panel has one input signal interface. To this, a 

timer or a door switch is usually connected.

Type CA M-150-W-F

Code 1213

U 230 V 1N~ 50 Hz

Biddle bv
Markowei 4
NL-9288 HA Kootstertille

Nº 5426/1-1  00-01

I

max

L1 2.4 A

I

max

L2 -

M 60 kg

I

max

L3 -

Medium LPHW

P

motor

0.56 kW

p

max

1400 kPa

P

heating

-

code

Summary of Contents for CA M-150-W-F





























































Reviews:

No comments