SELETTO - Ver. 05 -
7
D811409_05
INSTALLATION MANUAL
ENGLISH
Thank you for buying this product, our company is
sure that you will be more than satisfied with the
product’s performance. The product is supplied with
a “
Warnings
” leaflet and an “
Instruction booklet
”.
These should both be read carefully as they provide
important information about safety, installation,
operation and maintenance. This product complies
with the recognised technical standards and sa-
fety regulations. We declare that this product is in
conformity with the following European Directives:
2004/108/EEC and 73/23/EEC (and subsequent
amendments).
GENERAL SAFETY
WARNING! An incorrect installation or improper
use of the product can cause damage to persons,
animals or things.
• Scrap packing materials (plastic, cardboard, po
-
lystyrene etc) according to the provisions set out
by current standards. Keep nylon or polystyrene
bags out of children’s reach.
• Keep the instructions together with the technical
brochure for future reference.
• This product was exclusively designed and ma
-
nufactured for the use specified in the present
documentation. Any other use not specified in
this documentation could damage the product
and be dangerous.
• The Company declines all responsibility for any
consequences resulting from improper use of
the product, or use which is different from that
expected and specified in the present documen
-
tation.
• Do not install the product in explosive atmosphere.
• Disconnect the electrical power supply before
carrying out any work on the installation. Also
disconnect any buffer batteries, if fitted.
• Only use original parts for any maintenance or
repair operation.
• Instruct the product user about the control systems
provided and the manual opening operation in
case of emergency.
• Do not allow persons or children to remain in the
automation operation area.
• Keep radio control or other control devices out of
children’s reach, in order to avoid unintentional
automation activation.
• The user must avoid any attempt to carry out work
or repair on the automation system, and always
request the assistance of qualified personnel.
• Anything which is not expressly provided for in
the present instructions, is not allowed.
• Fit an omnipolar or magnetothermal switch on the
mains power supply, having a contact opening
distance equal to or greater than 3,5 mm.
• Check that a differential switch with a 0.03A
threshold is fitted just before the power supply
mains.
• The power supply must have a very low safety
voltage and the generator must be protected
against short circuit.
1) GENERAL OUTLINE
Programmable digital pushbutton panel for control
-
ling pedestrian and vehicle access points using two
operating methods:
1 - Serial connection:
Manages control panels provided with serial
connection.
Up to 16 different codes can be memorised. Each
valid code sends a start command through the
serial line.
2 - Interfaced with a Compass system:
The pushbutton panel is integrated in the Com
-
pass access control system.
Provided with an anti-break-in metal container,
the Seletto pushbutton panel does not directly
control access point opening. Therefore, it can
also be safely installed in unprotected areas.
2)TECHNICAL SPECIFICATIONS
Power supply:
................12/24 V
~
/ ±10% 50Hz
Absorption:
..................................................
60 mA
Working temperature:
......................... -10 / +55°C
No. codes (serial connection):
...........................
16
Dimensions: ............................................
see fig. 1
Degree of protection: .....................................
IP 44
3) INSTALLATION
Various types of mounting are possible:
3.1) Recessed mounting on wall (SELETTO)
Make a hole where the supplied plastic container is
to be inserted, this will be held in place by concrete
filling (Fig. 1a).
3 fixing clips are supplied (Fig. 1a “G”) to be scre
-
wed on the container before carrying out concrete
filling.
After the concrete has set, the 3 screws must be
removed to allow the gasket and metal ring nut to
be subsequently fitted.
3.2) Recessed mounting on metal pillar (SE-
LETTO)
Make a hole by means of a ø 60 milling cutter where
the supplied plastic container is to be inserted. To
fix the container, drill three ø 3.6 holes for the three
self-tapping screws.
3.3) External container mounting (SELETTO E)
Use the box as a drilling template and drill 4 holes.
Fix by means of self-tapping screws or expansion
plugs, depending on the surface the box is being
fixed
on. Use the black sponge (H) between the
appliance and the wall (Fig.1b).
