background image

 

 

 

LIMITED WARRANTY 

Bercomac Limitée 

92, Fortin North, Adstock, Quebec, Canada, G0N 1S0

 

Conditions and Products Covered: 

 

BERCOMAC guarantees any part of the product or accessory 

manufactured by BERCOMAC and found in the reasonable 

judgment of BERCOMAC to be defective in material and or 

workmanship will be repaired or replaced by an authorized 

dealer without charge up to our maximum labor rates and pre-

established times.  For replacement parts only standard ground 

freight services are covered.  This warranty extends to the 

original retail purchaser only and is not transferable to any 

subsequent purchasers. This warranty applies to the products 

bought and used in North America. 

 

Warranty Period  

(from date of the original retail purchase): 

 

 

Residential or semi-commercial use: 1 year 

 

Commercial, professional or rental use: 90 days 

 

Exceptions Noted Below; the following items are guaranteed 

by the original manufacturer and have their own warranty, 

conditions and limited time: 

 

 

 

Tire Chains: 90 days 

 

Engines: Will vary as per the manufacturer 

  Please refer to the engine manufacturer’s warranty 
 statement included with the unit.  BERCOMAC is not 

  authorized to handle warranty adjustments on engines.

 

 

Items and Conditions NOT Covered: 

 

This warranty does not cover the following: 

 

 

Pick-up or delivery charges or in-home services fees. 

 

Any damage or deterioration of the unit, parts and or finish 

of these due to normal use, wear and tear, or exposure. 

 

Cost of regular use or maintenance service or parts, such as 

gas, oil, lubricants, tune-up parts, and adjustments. 

 

Any part or accessory which has been altered, modified, 

misused, neglected, accidentally damaged or not properly 

installed, maintained, stored or repaired not in accordance 

with the instructions in the owner’s manual.  

 

Repair due to normal wear and or any wear items include 

but are not limited to items such as shear pins, bolts, belts, 

winch cables, cutting edge, skid shoes etc. 

 

Expedited freight fee services for replacement parts. 

 

Shear bolts and shear pins are to be considered as a 

preventive measure not as an assured protection, any 

damages resulting from the lack of shear bolts breakage are 

not covered. 

NOTE: All warranty work must be performed by an authorized 

dealer using original (manufacturer) replacement parts. 

 
Owner’s Responsibilities: 

 

Any defective equipment or part must be returned to an 
authorized dealer within the warranty period for repairs.  In the 
event that defective merchandise must be returned to 

manufacturer for repairs, the dealer must first obtain a written 
authorization from either KIMPEX or BERCOMAC, freight fees 
are prepaid prior to the shipment.  This warranty extends only 

to equipment operated under normal conditions.  To validate a 
warranty claim, it is the user’s responsibility to maintain and 

service the unit as specified in the owner’s manual or to have 
the unit serviced at their dealer at their expense.    

 

General Conditions: 

 

The sole liability of BERCOMAC with respect to this warranty 
shall be strictly and exclusively repair and replacement as 

mentioned herein.  BERCOMAC shall not have any liability for 
any other costs, loss or damage, including but not limited to, 

any incidental or consequential loss or damage. 
 
Taking advantage of the warranty does not in any way extend 

the length or renewal of the warranty. 

 

In particular, without being limited to, BERCOMAC shall have 
no liability or responsibility for: 

 

 

Travel time, overtime, after hours time or other 

extraordinary repair charges or relating to repairs and or 
replacements outside of normal business hours. 

 

Rental of like or similar replacement equipment during the 
period of any, repair or replacement work. 

 

Any communicating or travel charges. 

 

Loss or damage to person or property other than that 

covered by the terms of this warranty. 

 

Any claims for lost revenue, lost profit or any similar costs 

as a result of damage or repair. 

 

Attorney’s fees.   

 

BERCOMAC’s responsibility in respect to claims is limited to 
making the required repairs or replacement without charge up 

to our maximum labor rates and pre-established times and no 
claim of breach of warranty shall be cause for cancellation or 
rescission of the contract of sale of any product or accessory. 

In no event shall recovery of any kind be greater than the 
amount of the purchase price of the product sold. 

 

This warranty gives you specific legal rights.  You may also 
have other rights, which vary from state to state

NOTE:  Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify 

any product previously manufactured. 

Instructions for Obtaining Warranty Services:

 

Contact dealer where equipment was purchased or any other authorized service dealer to arrange service at their dealership. Requests 

for warranty claims must be carried out through the same distribution network used to purchase the product. Don't forget to bring your 
proof of purchase (sales receipt) to the dealer.

 

Summary of Contents for 700512-3-66













































Reviews: