background image

27

EN

CLR

By selecting this function, the receiver goes into waiting (

Push

) for a transmitter code to erase from the memory. 

If the code is valid, it is erased and the message 

OK 

is displayed

If the code is not valid or not present in memory, the message 

Err 

is displayed

RTR

Completely erases memory of the receiver. Confirmation of the operation is requested. 
By selecting this function the receiver goes into waiting (

Push

) for a new PGM pressure to confirm the operation. 

At end of erasing the 

OK

 message is displayed

8.4.4) CYCLES NUMBER (

NMAN

)

Displays the number of complete cycles (open+close) carried out by the automation. When the <PG> button is pressed for the first time, it displays 
the first 4 figures, the second time it shows the last 4. Example <PG> 

0012 

>>> <PG> 

3456

: made 123.456 cycles.

8.4.5) MAINTENANCE CYCLES (

MACI

)

This function enables to activate the maintenance request notice after a number of manoeuvres determined by the installer. 
To activate and select the number of manoeuvres, proceed as follows: 
Press button <PG>, the display will show OFF, which indicated that the function is disabled (default value). 
With the buttons <+> and <-> select one of the numeric values proposed (from OFF to 100). The values are intended as hundreds of cycles of ma-
noeuvres (for example: the value 50 indicates 5000 manoeuvres). 
Press the OK button to activate the function. The display will show the message 

PROG

The maintenance request is indicated to the user by keeping the indicator lamp lit up for other 10 sec after the conclusion of the opening or closing operation.

8.4.6) RESET (

RES

)

RESET of the control unit. ATTENTION!: Returns the control unit to the default values.
Pressing the <PG> button for the first time causes blinking of the letters 

RES

, pressing the <PG> button again resets the control unit. Note: The trans-

mitters are not erased from the receiver nor is the access password and the configuration of synchronism. 
All the logics and all the parameters are brought back to default values, it is therefore necessary to repeat the autoset procedure. 

8.4.7) AUTOSET (

AUTO

)

This function sets the optimal functioning values of the installation, at the end of the procedure, it sets the average values of torque (PMO/PMC and 
PSO/PSC). To carry out the AUTOSET, proceed as follow:
a) Make sure that during the autoset there is no obstacle is in the maneuver area, if necessary, fence off the area so that persons, animals, cars, etc., 
cannot interrupt the procedure. 

During the autoset phase, the anti-crushing function is not active, while the activation of inputs and safety devices generates an error. 
(paragraph 8.10)

b) select the function AUTO and press PG.
c) the control unit waits the confirmation to start the procedure "AUTO" FLASHING.
d) press PG to start the AUTOSET procedure.
The control unit performs few maneuvers for the stroke learning and the configuration of the parameters. In case that the procedure is not successful 
the message ERR will be shown. Repeat the procedure after checking the wirings and the possible presence of obstacles.

8.4.8) PASSWORD (

CODE

)

It allows to type in an access protection code to the programming of the control unit.
A four-character alphanumeric code can be typed in by using the numbers from 0 to 9 and the letters A-B-C-D-E-F.
The default value is 0000 (four zeros) and shows the absence of a protection code.
While typing in the code, this operation can be cancelled at any moment by pressing keys + and – simultaneously. Once the password is typed in, it is pos-
sible to act on the control unit by entering and exiting the programming mode for around 10 minutes in order to allow adjustments and tests on functions.
By replacing the 0000 code with any other code, the protection of the control unit is enabled, thus preventing the access to any other menu. If a pro-
tection code is to be typed in, proceed as follows:
- select the Code menu and press OK.
- the code 0000 is shown, also in the case a protection code has been previously typed in.
- the value of the flashing character can be changed with keys + and -.
- press OK to confirm the flashing character, then confirm the following one. 
- after typing in the 4 characters, a confirmation message “CONF” appears.
- after a few seconds, the code 0000 appears again
- the previously stored protection code must be reconfirmed in order to avoid any accidental typing in.
If the code corresponds to the previous one, a confirmation message “

OK

” appears.

The control unit automatically exits the programming phase. To gain access to the Menus again, the stored protection code must be typed in.

IMPORTANT: TAKE NOTE of the protection code and KEEP IT IN A SAFE PLACE for future maintenance operations. To remove a code from 
a protected control unit it is necessary to enter into programming with the password and bring the code back to the 0000 default value. 
IF YOU LOOSE THE CODE, PLEASE CONTACT THE AUTHORISED SERVICE CENTER FOR THE TOTAL RESET OF THE CONTROL UNIT.

8.4.9) SYNCHRONIZATION (

BUS

)

MENU

FUNZIONE

id

Sets the synchronizing number. It is possible to set a numeric value from 0 to 16.
If the ID parameter is to 0 the control unit is set as MASTER, all the other values set the door as SLAVE.

loc

Allows a door set as SLAVE to receive local commands.
See paragraph 8.5 “SYNCHRONIZATION OF TWO OPPOSITE SLIDING DOORS”

Summary of Contents for BULL 1224 TURBO













































































Reviews: