BendPak PL-6000DC Page 7 Installation And Operation Manual Download

Page: 7 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

•

BendPak recommends making a

thorough

inspection of the Lift at least once a year. Replace

any damaged or severely worn parts, decals, or warning labels.

Symbols

Following are the symbols used in this Manual:

⚠

DANGER

Calls attention to an immediate hazard that

will

result in death or severe injury.

⚠

WARNING

Calls attention to a hazard or unsafe practice that

could

result in death or severe

personal injury.

⚠

CAUTION

Calls attention to a hazard or unsafe practice that could result in minor personal

injury, product damage, or property damage.

NOTICE

Calls attention to a situation that, if not avoided, could result in product or property
damage.

Liability Information

BendPak Inc. assumes

liability for damages resulting from:

• Use of the equipment for purposes other than those described in this Manual.
• Modifications to the equipment without prior, written permission from BendPak.
•

Modifying, disabling, overriding, or removing safety features.

• Damage to the equipment from external influences.
• Incorrect operation of the equipment.

Summary of Contents for PL-6000DC
























































































Search results

Summary of Contents for PL-6000DC

Reviews:

Related manuals for PL-6000DC

Brands by name

Popular brands

BendPak PL-6000DC, Installation And Operation Manual

Search results

Summary of Contents for PL-6000DC

Reviews:

Related manuals for PL-6000DC

Brands by name

Popular brands