manualshive.com logo in svg

BendPak PL-6000DC, Installation And Operation Manual, Page: 50 / 88

Share
Download
BendPak PL-6000DC Installation And Operation Manual Download Page 50

 

PL-6000DC Two Post Parking Lift 

50

 

P/N 5900273 — Rev. A1 — May 2022 

Install the Thermal Disconnect Switch 

⚠

 WARNING

 

The motor on the Power Unit supplied with your Lift has no thermal overload 
protection. 

Have the Electrician connect a Motor Thermal Disconnect Switch or overload device that will shut 

down the equipment in the event of an overload or an overheated motor. 

⚠

 

DANGER

 

Installing a Thermal Disconnect Switch 

must

 be performed by a licensed, certified 

Electrician. Do not perform 

any

 maintenance or installation on the Lift without first 

making sure that main electrical power has been disconnected from the Lift and 

cannot

 be re-energized until all procedures are complete.

 

High electrical current that exceeds the motor’s full load amps (FLA) rating may result in permanent 
damage to the motor. BendPak strongly recommends you 

not

 exceed the rated duty cycle of the 

motor. 
Refer to the 

Wiring Diagram

 and 

Control Console Wiring Diagram

 for further information. 

Install the Limit Switch Cord Grip and Wiring 

Several different Hydraulic Power Units may be supplied with this Lift and there may be minor 

variations in appearance. Using a conduit Knockout Punch create a hole in the Power unit’s Junction 

Box in an area that will not interfere with the existing electrical or mechanical components. A 
suggested location is pictured in the sketch below. Install the Thermal Disconnect in accordance with 

the manufacturer’s instructions. 
Refer to the 

Wiring Diagram

 and 

Control Console Wiring Diagram

 for further information. 

 

 

 

 

Summary of Contents for PL-6000DC

























































































Reviews:

No comments