BendPak PL-6000DC Page 65 Installation And Operation Manual Download

Page: 65 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Power Unit

Hydraulic Cylinder

Problem

Possible cause

Solution

Pressure cannot be

maintained after Platform
is Lifted.

Solenoid Valve element is

blocked.

Clean or replace Solenoid valve.

Outlet fitting is not fastened or

seal is damaged.

Reattach Outlet Pipe or replace

seal.

Dirty Hydraulic Oil.

Replace Hydraulic Oil.

Cylinder retracts slowly

when lowering.

Throttle Valve is not adjusted.

Adjust Throttle Valve.

Throttle valve is blocked.

Clean or replace Valve.

Solenoid Valve is blocked.

Clean or replace Valve.

Cylinder does not retract

at all when lowering.

Lowering Valve blocked.

Clean or replace valve.

Lowering solenoid is inoperative

or supply voltage is too low.

Replace Solenoid Coil or supply

correct voltage to the coil.

Cylinder worn or broken.

Replace the Cylinder.

Lift is too loud, or Lift is

making an abnormal

noise when Power Unit is

on.

Motor is inoperative.

Replace motor.

Low Hydraulic Fluid allows air into

pump and system.

Refill Reservoir. Run the Lift up

and down several times to bleed
air out of the system.

Pressure Relief Valve is triggered. Remove excess weight.

Inlet Filter is blocked.

Clean or replace filter.

Hydraulic Oil is dirty.

Replace Hydraulic Oil.

Pressure relief valve is
inoperative.

Replace Pressure Relief Valve.

Motor does not function. Input Voltage too low.

Correct the low voltage.

Voltage drop due to wrong wire

gauge for distance.

Replace the wire with the correct

wire gauge for the distance.

Starting Capacitor inoperative.

Replace starter Capacitor.

Summary of Contents for PL-6000DC
























































































Search results

Summary of Contents for PL-6000DC

Reviews:

Related manuals for PL-6000DC

Brands by name

Popular brands

BendPak PL-6000DC, Installation And Operation Manual

Search results

Summary of Contents for PL-6000DC

Reviews:

Related manuals for PL-6000DC

Brands by name

Popular brands